Snap-on Enclosure - case for Feather RP2040 DVI

This module enables the Feather series range to be expanded with 8 12-bit PWM outputs that can be used, for example, to control servos or LED diodes. Adafruit 2928

The expansion module (shield) is designed for Feather nRF52840 boards. It enables easy connection of 16x32, 32x32 and 64x32 matrix displays. Requires self-assembly. Adafruit 4702

An extension that allows you to connect classic 3.5" and 5.25" floppy drives to Feather boards, allowing you to read and write data using the original interface. A built-in logic level converter ensures safe operation with 5V devices, and compatibility with the Feather M4 and RP2040 ensures adequate performance when streaming data. Adafruit 5679

These add-ons for any Feather board will let you integrate packetized radio (with the RFM69 radio) or LoRa radio (with the RFM9x\'s). These radios are good options for kilometer-range radio, and paired with one of our WiFi, cellular or Bluetooth Feathers, will let you bridge from 433/900 MHz to the Internet or your mobile device. Adafruit 3232

Feather board will let you integrate packetized radio (with the RFM69 radio) or LoRa radio (with the RFM9x\'s). These radios are good options for kilometer-range radio, and paired with one of our WiFi, cellular or Bluetooth Feathers, will let you bridge from 433/900MHz to the Internet or your mobile device. Adafruit 3230

An expansion board for Feather boards, featuring a 1.3-inch 128x64 monochrome OLED display and three user buttons. The board comes fully assembled and communicates via I2C, allowing for easy connection to other STEMMA QT devices. The SH1107 display provides high contrast with low power consumption, and a built-in reset button allows for quick system restarts. Adafruit 6313

OLED display with a diagonal of 1.3" and a resolution of 128x64 pixels. Designed for use with Feather series plates. Adafruit 4650

A versatile extension for Adafruit Feather boards, allowing you to quickly connect Grove modules and Stemma QT accessories without soldering. The module offers three Grove A/D connectors, one UART, and two I2C connectors, making it easy to expand your project with a variety of sensors and interfaces. An additional Stemma QT port allows for further expansion of I2C devices. Adafruit 5862

Module with a GPS receiver based on the MTK3333 system. Dedicated to Feather plates, communicates via the UART interface. Adafruit 3133

Module with monostable relay. It allows you to control high-power elements with a microcontroller. Adafruit 3191

Module with a matrix LED RGB 6x12 display (72 LEDs) designed to work with Feather plates. It communicates via a two-wire SPI interface. Adafruit 3449

This module allows you to add high-speed WiFi connectivity to your Feather-based projects, using the ESP32 as a network coprocessor. Support for TLS/SSL protocols and 8MHz high-speed SPI communication ensures stable and secure internet connections without burdening the main microcontroller. The module works with both 3.3V and 5V devices, and the built-in voltage regulator and MISO buffer facilitate integration with other FeatherWings. Adafruit 4264

Data logger dedicated to Thing Plus tiles. It allows you to save data on a microSD card with the possibility of reading through the USB port. Supports cards up to 32 GB. SparkFun DEV-19217

7-segment display controller, allowing communication over the I2C bus. Allows you to limit the pins needed to control the display. Adafruit 3088

This is the FeatherWing OLED: it adds a 128x32 monochrome OLED plus 3 user buttons to any Feather main board. Using our Feather Stacking Headers or Feather Female Headers you can connect a FeatherWing on top of your Feather board and let the board take flight. Adafruit 2900

The pad for use with shallow Feather series contains two TB6612 chips that allow you to control DC motors or stepper motors. The I2C interface is used to communicate with the overlay. Adafruit 2927