SparkFun Qwiic Shield - Shield with Qwiic connectors for Thing Plus

Module with a GPS receiver based on the MTK3333 system. Dedicated to Feather plates, communicates via the UART interface. Adafruit 3133

Data logger dedicated to Feather plates. Equipped with RTC clock, battery slot and micro SD card slot. Adafruit 2922

Data logger dedicated to Thing Plus tiles. It allows you to save data on a microSD card with the possibility of reading through the USB port. Supports cards up to 32 GB. SparkFun DEV-19217

Pin expander designed for Feather plates. It is equipped with three sets of female strips and holes for prototyping. Adafruit 3417

7-segment display controller, allowing communication over the I2C bus. Allows you to limit the pins needed to control the display. Adafruit 3088

DS3231 Precision RTC FeatherWing adds an extremely accurate I2C-integrated Real Time Clock (RTC) with a Temperature Compensated Crystal Oscillator (TCXO) to any Feather main board. Adafruit 3028

The compact enclosure for the Adafruit Feather RP2040 with DVI output is printed using SLA technology in semi-transparent plastic, providing protection and visibility of the LED indicators. It allows easy access to all ports and buttons, and the snap-in design eliminates the need for screws or glue. Adafruit 6241

This compact development board allows direct connection to 24-pin e-paper displays, ideal for energy-efficient visual projects. Equipped with a 133MHz RP2040 microcontroller, 264KB SRAM, and 8MB Flash, it offers smooth display caching and support for a wide range of peripherals. It features a dedicated SPI display interface, a STEMMA QT connector, a Li-Po charger, USB-C, and a comprehensive GPIO set with PWM, ADC, and I2C, SPI, and UART communication. Adafruit 5727

Module with 3-axis accelerometer ADXL343 and precise temperature sensor ADT7410 dedicated to Feather series boards. Equipped with a STEMMA QT connector, it communicates via the I2C interface. Adafruit 4147

The pad for use with shallow Feather series contains two TB6612 chips that allow you to control DC motors or stepper motors. The I2C interface is used to communicate with the overlay. Adafruit 2927

This is the FeatherWing OLED: it adds a 128x32 monochrome OLED plus 3 user buttons to any Feather main board. Using our Feather Stacking Headers or Feather Female Headers you can connect a FeatherWing on top of your Feather board and let the board take flight. Adafruit 2900

A prototyping extension for Feather boards, allowing you to connect up to three additional FeatherWings simultaneously without using stacked connectors. The board offers three pins for each Feather pin, shared 3.3V and GND power lines, and a prototyping area with a grid of holes for adding your own components. Compatible with all Feathers, it\'s ideal for prototyping and expanding your projects. Adafruit 4254

Module with monostable relay. It allows you to control high-power elements with a microcontroller. Adafruit 2895

The expansion module (shield) is designed for Feather nRF52840 boards. It enables easy connection of 16x32, 32x32 and 64x32 matrix displays. Requires self-assembly. Adafruit 4702

Extension module dedicated to matrix displays with HUB75 interface. Designed for Feather RP2040, M0 and M4 series tiles. Adafruit 3036

These add-ons for any Feather board will let you integrate packetized radio (with the RFM69 radio) or LoRa radio (with the RFM9x\'s). These radios are good options for kilometer-range radio, and paired with one of our WiFi, cellular or Bluetooth Feathers, will let you bridge from 433/900 MHz to the Internet or your mobile device. Adafruit 3232