SparkFun Qwiic Shield - Shield with Qwiic connectors for Arduino Nano

Module with three optical inspection sensors (spectrophotometers) from the AS7265x series. The module consists of three sensors; AS72651, AS72652 and AS72653 which can detect wavelengths from 410nm (UV) to 940nm (IR). SparkFun SEN-15050

Optical Time of Flight sensor with Pmod I2C connector. The built-in ISL29501 digital signal processor calculates the time it takes for the light emitted by ToF to reach the destination and back. The calculated time is proportional to the distance. Pmod ToF has a range of up to 5 m. Digilent 410-392

Module with a button and re LED backlight. Controlled by the I2C interface, it has a built-in debouncing mechanism, pull-up resistors as well as interrupts and a FIFO queue. SparkFun BOB-15932

SparkFun weather: bit module designed for micro: bit, with temperature, humidity and pressure sensor (BME280 system). In combination with the micro: bit module, it is possible to build a fully functional weather station. SparkFun DEV-15837

The SparkFun micro:climate kit is a full weather station kit that is built on top of the weather:bit carrier board. The set contains all the elements needed to build a weather station. Sparkfun KIT-16274

Evaluation kit with Sparkfun Artemis Bluetooth 5.0 module designed on the basis of the Feather kit. It has a USB C. The board also has a USB-UART converter, a microphone and a JTAG debugging connector. Artemis has support in the Arduino IDE. SparkFun WRL-15574

Evaluation kit with RISC-V Dual Core 64bit chip and WiFi ESP32 chip. Equipped with a USB-UART converter, MEMS microphone, OV2640 camera and a microSD card slot. The set is compatible with Arduino UNO Rev3. Seeed Studio 102991184

Evaluation kit with STM32H7B3LIH6QU microcontroller with 2MB Flash memory and 1.4MB RAM memory. Equipped with a TFT display with a touch screen, WiFi module and numerous peripherals and connectors. STMicroelectronics STM32H7B3I-DK

Compact programmer module for STM32 microcontrollers for soldering into a board. Supports JTAG/SWD interfaces. STLINK-V3SET has a virtual COM port and interfaces SPI, I2C, CAN, GPIO for programming via bootloader. STMicroelectronics STLINK-V3MODS

Evaluation kit from the STM32 Nucleo-144 series equipped with the STM32L4P5ZGT6U microcontroller in the LQFP144 package. A large number of pins allows you to create complex devices using the numerous peripherals available in the microcontroller. STMicroelectronics NUCLEO-L4P5ZG

Evaluation kit from the STM32 Nucleo-144 series equipped with the STM32L552ZE microcontroller in the LQFP144 enclosure. A large number of pins allows you to create complex devices using the numerous peripherals available in the microcontroller. STMicroelectronics NUCLEO-L552ZE-Q

Expansion board for STM32 Nucleo based on S2-LP RF transmitter operating in 868MHz band. The expansion board is compatible with ST morpho and Arduino UNO R3 connectors. STMicroelectronics X-NUCLEO-S2868A2

An expansion board with several EEPROM memories from the M24xx and M95xx series, designed to work with STM32 Nucleo boards. STMicroelectronics X-NUCLEO-EEPRMA2

Expansion board for STM32 Nucleo designed for applications using MEMS analog microphones. The board is compatible with STM32 Nucleo and Arduino UNO R3 connectors. STMicroelectronics X-NUCLEO-AMICAM1

The MPLAB Snap In-Circuit Debugger/Programmer allows affordable, fast and easy debugging and programming of PIC, dsPIC, AVR and SAM flash MCUs. Microchip PG164100

SparkFun micro:bot kit v2.0 - is the perfect controller for learning how to build and program robots. The combination of micro:bit with the SparkFun moto:bot carrier board creates an efficient, cheap robotics platform with Qwiic support for robot enthusiasts of all ages. With SparkFun micro:bot, you can quickly create simple robots. SparkFun kit-16275