X-NUCLEO-LED16A1 - 16 channel LED driver expansion board

Time-of-Flight VL53L3CX Distance Sensor Expansion Board. The set is designed to measure distances and detect gestures. Distance measurement was carried out using VL53L3CX laser sensors. STMicroelectronics X-NUCLEO-53L3A2

X-NUCLEO-IDS01A5 is a development board STM32 Nucleo that allows you to use the RF SPSGRF-915 module on the ISM band (915 MHz carrier).

Shield for STM32 Nucleo that allows you to add the possibility of operating a three-phase brushless motor (BLDC) or synchronous permanent magnet (PMSM). It uses the L6230 chip for control. X-NUCLEO-IHM07M1

Shield with MEMS sensors: accelerometer, gyroscope, magnetometer, pressure, humidity and temperature sensor. Shield is designed to work with plates from the STM32 Nucleo family (connector in accordance with the Arduino UNO R3 standard). Sensors use I2C interface for communication. STMicroelectronics X-NUCLEO-IKS01A3

The X-NUCLEO-53L0A1 expansion board features the VL53L0X ranging and gesture detection sensor, based on ST’s FlightSense™, Time-of-Flight technology. It is an evaluation board that provides an introduction to the ranging and gesture detection capabilities of the VL53L0X module

The STEVAL-FKI433V2 evaluation board is based on the S2-LP sub-1GHz ultra-low power low data-rate transceiver suitable for ISM bands and wireless M-Bus. The NUCLEO-L053R8 motherboard is equipped with an STM32L0 low power microcontroller to control the S2-LP

The X-NUCLEO-LPM01A is a 1.8 V to 3.3 V programmable power supply source with advanced power consumption measurement capability

The X-NUCLEO-IHM15A1 dual brush DC motor driver expansion board is based on the STSPIN840 for STM32 Nucleo. It provides an affordable and easy-to-use solution for the implementation of compact motor driving applications such as thermal printers, robotics and toys

The X-NUCLEO-IHM11M1 is a low voltage three-phase brushless DC motor driver expansion board based on the STSPIN230 for STM32 Nucleo. It provides an affordable and easy-to-use solution for the implementation of portable motor driving applications such as thermal printers, robotics and toys

An expansion board with digital outputs (for industrial applications) designed to work with the STM32 Nucleo kits. The module is based on a single high-side switch IPS160HF. STMicroelectronics X-NUCLEO-OUT08A1

Expansion board with LCD TFT 2.2 "display for STM32 Nucleo sets. Equipped with SPI NOR Flash 64Mbit memory for storing images and a joystick for GUI navigation. STMicroelectronics X-NUCLEO-GFX01M2

Multifunctional board for STM32 NUCLEO, built based on operational amplifiers. Has, among others built-in LED current controller, prototype area and window discriminator

Expansion board for STM32 Nucleo enabling output support in the industry standard. It allows you to control eight galvanically isolated outputs as relays. It has a connector compatible with Arduino® UNO R3. STMicroelectronics X-NUCLEO-OUT02A1

P-NUCLEO-IOD02A1 is an STM32 Nucleo kit consisting of NUCLEO-L452RE (IO-Link stack), X-NUCLEO-IOD02A1 (IO-Link physical layer) and X-NUCLEO-IKS02A1 (sensor module). The kit constitutes a full IO-Link device. P-NUCLEO-IOD02A1

DC motor controller powered with a voltage in the range of 1.8 to 10V with a maximum output current of 2.6A. Compatible with STM32 Nucleo. Shield is equipped with a connector compatible with the Arduino UNO R3 standard. STMicroelectronics X-NUCLEO-IHM13A1

Extension module for STM32 Nucleo based on a two-channel SIO transceiver and IO-Link PHY L6364Q with built-in voltage stabilizers and a DC-DC converter. STMicroelectronics X-NUCLEO-IOD02A1