X-NUCLEO-IOD02A1 - Dual-channel IO-Link device expansion module for STM32 Nucleo
ID: 581676
5906623410682
zł128.28
Tax included
zł104.29 tax excl.
Extension module for STM32 Nucleo based on a two-channel SIO transceiver and IO-Link PHY L6364Q with built-in voltage stabilizers and a DC-DC converter. STMicroelectronics X-NUCLEO-IOD02A1
Description
X-NUCLEO-IOD02A1 is an expansion module for STM32 Nucleo based on a two-channel SIO transceiver and IO-Link PHY L6364Q with built-in voltage stabilizers 50 mA 3.3 V and 5 V and a DC-DC converter.
The expansion board provides an inexpensive and easy-to-use solution for SIO and IO-Link industrial sensor application development. X-NUCLEO-IOD02A1 communicates with the STM32 microcontroller through the SPI and GPIO pins and is compatible with Arduino UNO R3 and ST morpho connectors (not mounted). It can work with the NUCLEO-L073RZ or NUCLEO-G071RB kits.
Communication via IO-Link can take place in multi-byte and single-byte mode or in transparent mode. On-board switches allow configuration of the L6364Q and expansion card settings such as transmission mode and DC-DC converter on/off according to application requirements.
Features
- Based on the L6364Q IO-Link device dual transceiver in QFN package with the following main characteristics:
- 2-channel (CQ and DIO) IO-Link PHY layer
- IO-Link DLL (M-sequence handler and checksum)
- Wake-up detection
- Interrupt diagnostic pin
- SPI and UART interfaces
- 50 mA 3.3 V and 5.0 V linear regulators
- 50 mA adjustable (5.0 ÷ 10.8 V) buck converter
- Overload protection with adjustable intervention threshold
- Overheating protection with adjustable shutdown threshold
- Full reverse polarity on process side
- Ground and VCC wire break protections
- QFN-20L (4 x 4 x 0.9 mm) package
- 5 to 35 V operating voltage range
- Red LED and green LED for status diagnostics
- Radiated Emissions (EM Fields 30 MHz-1 GHz) < 40dB µV/m
- Immunity to conducted disturbance (150 kHz-80 MHz) ≤ 10 V
- Immunity to RF EM Fields (80 MHz-1 GHz) ≤ 10 V/m
- Immunity to RF EM Fields (1 GHz-2.7 GHz) ≤ 3 V/m
- Immunity to SURGE pulse (500 Ohm coupling) ≤ ± 1.2 kV
- Immunity to ESD contact/air ≤ ±3 kV
- Immunity to BURST noise ≤ ±1 kV
- Compatible with STM32 Nucleo development boards
- Equipped with Arduino UNO R3 connectors
581676
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
STM32 Nucleo-64 development board with STM32L073RZT6 MCU, supports Arduino and ST morpho connectivity
zł79.15
24h
Available quantity: 4
Available
The STM32 Nucleo-64 boards provide an affordable and flexible way for users to try out new concepts and build prototypes with the STM32 microcontrollers, choosing from various combinations of performance, power consumption and features
zł52.85
24h
Available quantity: 26
Available
The X-NUCLEO-IKS02A1 industrial motion MEMS sensor expansion board is compatible with the Arduino UNO R3 connector layout. STMicroelectronics X-NUCLEO-IKS02A1
zł145.67
24h
Available quantity: 1
Available
Other products in the same category (16)
The X-NUCLEO-53L1A1 is an expansion board for the NUCLEO-F401RE and NUCLEO-L476RG development boards. It provides a complete evaluation kit allowing anyone to learn, evaluate, and develop their applications using the VL53L1X ToF, long-distance ranging sensor technology.
zł262.51
24h
Available quantity: 1
Available
The X-NUCLEO-IHM17M1 is a low voltage three-phase brushless DC motor driver expansion board based on the STSPIN233 for STM32 Nucleo. It provides an affordable and easy-to-use solution for the implementation of portable motor driving applications such as thermal printers, robotics and toys
zł86.24
1 weeks
No product available!
The X-NUCLEO-STMODA1 provides an easy way to expand your STM32 Nucleo board with the STMod+ connector, which allows interaction with the new set of STM32 Nucleo development boards using this connector
zł119.72
24h
Available quantity: 1
Available
The X-NUCLEO-IHM15A1 dual brush DC motor driver expansion board is based on the STSPIN840 for STM32 Nucleo. It provides an affordable and easy-to-use solution for the implementation of compact motor driving applications such as thermal printers, robotics and toys
zł89.38
24h
Available quantity: 1
Available
The X-NUCLEO-S2868A1 expansion board is based on the S2-LP radio and operates in the 868 MHz ISM frequency band. The expansion board is compatible with ST morpho and Arduino UNO R3 connectors
zł208.50
1 weeks
No product available!
The X-NUCLEO-IHM16M1 motor driver expansion board is based on the STSPIN830 monolithic driver for three-phase brushless motors. It represents an affordable, easy-to-use solution for driving brushless motors in your STM32 Nucleo project, implementing single and three-shunt current sensing
zł78.20
24h
Available quantity: 1
Available
The STEVAL-FKI868V2 evaluation board is based on the S2-LP sub-1GHz ultra-low power low data-rate transceiver suitable for ISM bands and wireless M-Bus. The NUCLEO-L053R8 motherboard is equipped with an STM32L0 low power microcontroller to control the S2-LP
zł361.71
24h
Available quantity: 1
Available
The STEVAL-FKI433V2 evaluation board is based on the S2-LP sub-1GHz ultra-low power low data-rate transceiver suitable for ISM bands and wireless M-Bus. The NUCLEO-L053R8 motherboard is equipped with an STM32L0 low power microcontroller to control the S2-LP
zł368.37
24h
Available quantity: 1
Available
The X-NUCLEO-GNSS1A1 expansion board is based on the Teseo-LIV3F tiny GNSS module
zł213.00
24h
Available quantity: 2
Available
The X-NUCLEO-EEPRMA1 expansion board is based on M24xx I²C and M95xx SPI EEPROM for data reading and writing
zł97.37
24h
Available quantity: 1
Available
DC motor controller powered with a voltage in the range of 1.8 to 10V with a maximum output current of 2.6A. Compatible with STM32 Nucleo. Shield is equipped with a connector compatible with the Arduino UNO R3 standard. STMicroelectronics X-NUCLEO-IHM13A1
zł95.96
24h
Available quantity: 2
Available
The set consists of STM32 Nucleo NUCLEO-G431RB plate with STM32G431RB microcontroller, X-NUCLEO-IHM16M1 plate with three-phase STPIN830 BLDC / PMSM motor controller and GBM2804H-100T motor. STMicroelectronics P-NUCLEO-IHM03
zł355.90
24h
Available quantity: 1
Available
Expansion board for STM32 Nucleo enabling output support in the industry standard. It allows you to control eight galvanically isolated outputs as relays. It has a connector compatible with Arduino® UNO R3. STMicroelectronics X-NUCLEO-OUT02A1
zł143.05
24h
Available quantity: 2
Available
Expansion board compatible with STM32 Nucleo. Allows you to prototype solutions with digital microphones. STMicroelectronics X-NUCLEO-CCA02M2
zł139.09
24h
Available quantity: 3
Available
STM32 Nucleo starter pack for LoRa technology. It consists of two development kits: NUCLEO-L073RZ and NUCLEO-F746ZG and expansion modules for communication within LoRa: LRWAN_NS1 and LRWAN_GS_LF1. STMicroelectronics P-NUCLEO-LRWAN3
zł506.86
1 weeks
No product available!
The X-NUCLEO-IKS02A1 industrial motion MEMS sensor expansion board is compatible with the Arduino UNO R3 connector layout. STMicroelectronics X-NUCLEO-IKS02A1
zł145.67
24h
Available quantity: 1
Available
Extension module for STM32 Nucleo based on a two-channel SIO transceiver and IO-Link PHY L6364Q with built-in voltage stabilizers and a DC-DC converter. STMicroelectronics X-NUCLEO-IOD02A1