NUCLEO-L073RZ - STM32 Nucleo-64 development board with STM32L073RZT6 MCU

Cables for evaluation boards, set of 10 pcs., red colour

Cables for evaluation boards, set of 10 pcs., green colour

Cable with USB plugs type A and mini-USB type B, cable with a length of 1.8 m

Easy-to-use retractable cable with USB type A plugs and mini-B type, the cable is 73 cm long after being unrolled

Set of 10 pcs. Male blue male cables, 15 cm long, for contact plates. CAB_M-M (10-15-B)

Set of 10 pcs. Male-male orange male cables, 15 cm long, for contact plates. CAB_M-M (10-15 ORG)

A set of 40 female-female connection cables, in various colors, 17 cm long. CAB_F-F (Rainbow-40-17)

Set of 40 pcs of different colored male-male cables, 17 cm long, for contact plates. CAB_M-M (Rainbow-40-17)

Expansion board with a dynamic NFC/RFID tag based on the M24SR64-Y. The system is equipped with EEPROM memory, the module can be powered by the Arduino connector. STMicroelectronics X-NUCLEO-NFC01A1

Expansion board with L6474 stepper motor driver. It is equipped with a connector compatible with Arduino Uno R3 and STM32 Nucleo. STMicroelectronics X-NUCLEO-IHM01A1

Multifunctional expander (shield) for NUCLEO and Arduino equipped with Bluetooth 2.0+EDR (HC-05) interface, MEMS 3DoF LIS35, LED-RGB, joystick and analog STLM20 temperature sensor developed and produced by KAMAMI.

A functional expander for NUCLEO and Arduino with a set of environmental sensors: pressure, humidity, temperature and light intensity and also a 5-position joystick and LED RGB.

Extension board for SMT332 Nucleo with VL6180X sensor, allowing to measure ambient lighting, zoom and recognition of gestures. On the PCB, outside the sensor, there is also a four-digit LED display and connectors for additional sensors

X-NUCLEO-IDS01A4 is a development board STM32 Nucleo that allows the use of the RF SPSGRF-868 module for the ISM band (868 MHz carrier).

X-NUCLEO-IDS01A5 is a development board STM32 Nucleo that allows you to use the RF SPSGRF-915 module on the ISM band (915 MHz carrier).

The X-NUCLEO-IHM03A1 plate allows the control of a high-power stepper motor; the maximum current of the phase is 10A rms, additionally the controller enables execution up to 1/128 step and has a number of protections. X-NUCLEO-IHM03A1

Shield for STM32 Nucleo that allows you to add the possibility of operating a three-phase brushless motor (BLDC) or synchronous permanent magnet (PMSM). It uses the L6230 chip for control. X-NUCLEO-IHM07M1

Extension board X-NUCLEO-IHM04A1 for STM32 Nucleo, with dual brush motor controller, operating based on the L6206 system

The STM32 Nucleo expansion board allows you to control a bipolar stepper motor. The maximum phase current is 2.8A RMS, the controller has overheat protection and overcurrent protection

Industrial input/output expansion board based on VNI8200XP and CLT01-38SQ7 for STM32 Nucleo

Multifunctional board for STM32 NUCLEO, built based on operational amplifiers. Has, among others built-in LED current controller, prototype area and window discriminator

Expander (shield) compatible with Arduino and NUCLEO (STM32) systems, equipped with a Bluetooth 4.1 (BLE) radio module from the SPBTLE-RF family

A set of 50 MF wires in various colors, 20 cm long, with insulated terminals