X-NUCLEO-PGEEZ1 - Standard SPI Page - EEPROM memory expansion module

DC motor controller powered with a voltage in the range of 1.8 to 10V with a maximum output current of 2.6A. Compatible with STM32 Nucleo. Shield is equipped with a connector compatible with the Arduino UNO R3 standard. STMicroelectronics X-NUCLEO-IHM13A1

The X-NUCLEO-PLM01A1 expansion board for STM32 Nucleo is based on the ST7580 FSK, PSK multi-mode power line networking system-on-chip. It provides an affordable and easy-to-use solution for the development of connectivity applications based on power line communication

STM32 Nucleo expansion board designed to provide an application for the 16 channel LED driver LED1642GW. Depending upon the end application, RGB or single color LEDs can be connected to the board. Separate brightness control is possible for each channel. It is compatible with the STM32 Nucleo board family and equipped the Arduino™ UNO R3 connector layout. X-NUCLEO-LED16A1

The X-NUCLEO-IHM14A1 motor driver expansion board is based on the STSPIN820 monolithic driver for stepper motors.

Expansion board with BlueNRG-M0 module compatible with Bluetooth v4.2. It is compatible with the ST morpho connector system (unmounted) and Arduino UNO R3. Communication with the module is via the SPI interface. STMicroelectronics X-NUCLEO-IDB05A2

X-NUCLEO-IDS01A4 is a development board STM32 Nucleo that allows the use of the RF SPSGRF-868 module for the ISM band (868 MHz carrier).

The STEVAL-FKI433V2 evaluation board is based on the S2-LP sub-1GHz ultra-low power low data-rate transceiver suitable for ISM bands and wireless M-Bus. The NUCLEO-L053R8 motherboard is equipped with an STM32L0 low power microcontroller to control the S2-LP

Expansion board for STM32 Nucleo enabling output support in the industry standard. It allows you to control eight galvanically isolated outputs as relays. It has a connector compatible with Arduino® UNO R3. STMicroelectronics X-NUCLEO-OUT02A1

Expansion board with a dynamic NFC/RFID tag based on the M24SR64-Y. The system is equipped with EEPROM memory, the module can be powered by the Arduino connector. STMicroelectronics X-NUCLEO-NFC01A1

The X-NUCLEO-NFC02A1 is a dynamic NFC/RFID tag board based on M24LR04E-R, for expansion of STM32 Nucleo boards

Set consisting of the STM32 NUCLEO-F401RE board with the STM32F401RE microcontroller and the X-NUCLEO-53L4A2 board with the VL53L3CX ToF distance sensor. STMicroelectronics P-NUCLEO-53L4A2

The X-NUCLEO-53L0A1 expansion board features the VL53L0X ranging and gesture detection sensor, based on ST’s FlightSense™, Time-of-Flight technology. It is an evaluation board that provides an introduction to the ranging and gesture detection capabilities of the VL53L0X module

Expansion board equipped with VL6180 distance sensor, based on FlightSense technology. The set is designed to measure distances and detect gestures. X-NUCLEO-6180A1

The X-NUCLEO-LPM01A is a 1.8 V to 3.3 V programmable power supply source with advanced power consumption measurement capability

Expansion board with LCD TFT 2.2" display for STM32 Nucleo-144 sets. Equipped with SPI NOR Flash 64Mbit memory for storing images and a joystick for GUI navigation. STMicroelectronics X-NUCLEO-GFX02Z1

Multifunctional expander (shield) for NUCLEO and Arduino equipped with Bluetooth 2.0+EDR (HC-05) interface, MEMS 3DoF LIS35, LED-RGB, joystick and analog STLM20 temperature sensor developed and produced by KAMAMI.