X-NUCLEO-IHM14A1 - Stepper motor driver expansion board based on STSPIN820 for STM32 Nucleo

The X-NUCLEO-IHM12A1 is a low voltage dual brush DC motor driver expansion board based on the STSPIN240 for STM32 Nucleo. It provides an affordable and easy-to-use solution for the implementation of portable motor driving applications such as thermal printers, robotics and toys

The STM32 Nucleo expansion board allows you to control a bipolar stepper motor. The maximum phase current is 2.8A RMS, the controller has overheat protection and overcurrent protection

Multifunctional expander (shield) for NUCLEO and Arduino equipped with Bluetooth 2.0+EDR (HC-05) interface, MEMS 3DoF LIS35, LED-RGB, joystick and analog STLM20 temperature sensor developed and produced by KAMAMI.

The X-NUCLEO-53L0A1 expansion board features the VL53L0X ranging and gesture detection sensor, based on ST’s FlightSense™, Time-of-Flight technology. It is an evaluation board that provides an introduction to the ranging and gesture detection capabilities of the VL53L0X module

Shield for STM32 Nucleo that allows you to add the possibility of operating a three-phase brushless motor (BLDC) or synchronous permanent magnet (PMSM). It uses the L6230 chip for control. X-NUCLEO-IHM07M1

Time-of-Flight VL53L3CX Distance Sensor Expansion Board. The set is designed to measure distances and detect gestures. Distance measurement was carried out using VL53L3CX laser sensors. STMicroelectronics X-NUCLEO-53L3A2

The X-NUCLEO-IHM16M1 motor driver expansion board is based on the STSPIN830 monolithic driver for three-phase brushless motors. It represents an affordable, easy-to-use solution for driving brushless motors in your STM32 Nucleo project, implementing single and three-shunt current sensing

STM32 Nucleo starter pack for LoRa technology. It consists of two development kits: NUCLEO-L073RZ and NUCLEO-F746ZG and expansion modules for communication within LoRa: LRWAN_NS1 and LRWAN_GS_LF1. STMicroelectronics P-NUCLEO-LRWAN3

Expansion board for STM32 Nucleo designed for applications using MEMS analog microphones. The board is compatible with STM32 Nucleo and Arduino UNO R3 connectors. STMicroelectronics X-NUCLEO-AMICAM1

Expansion module designed for STM32 Nucleo-64 boards with built-in Power Delivery peripheral (UCPD). It allows prototyping of devices using the TCPP03-M20 system and USB type C in the DRP (Dual Role Power) and DRD (Dual Role Data) functions. STMicroelectronics X-NUCLEO-DRP1M1

Board with digital outputs designed to work with STM32 Nucleo. It is based on the IPS1025H single high-side switch circuit. STMicroelectronics X-NUCLEO-OUT05A1

The STEVAL-FKI433V2 evaluation board is based on the S2-LP sub-1GHz ultra-low power low data-rate transceiver suitable for ISM bands and wireless M-Bus. The NUCLEO-L053R8 motherboard is equipped with an STM32L0 low power microcontroller to control the S2-LP

The P-NUCLEO-53L1A1 is a complete evaluation kit allowing anyone to learn, evaluate, and develop their application using the VL53L1X ToF, long-distance ranging sensor technology

The X-NUCLEO-NFC02A1 is a dynamic NFC/RFID tag board based on M24LR04E-R, for expansion of STM32 Nucleo boards

The STEVAL-FKI868V2 evaluation board is based on the S2-LP sub-1GHz ultra-low power low data-rate transceiver suitable for ISM bands and wireless M-Bus. The NUCLEO-L053R8 motherboard is equipped with an STM32L0 low power microcontroller to control the S2-LP

Expansion board with BlueNRG-M0 module compatible with Bluetooth v4.2. It is compatible with the ST morpho connector system (unmounted) and Arduino UNO R3. Communication with the module is via the SPI interface. STMicroelectronics X-NUCLEO-IDB05A2