X-NUCLEO-OUT05A1 is an expansion board with digital outputs (for industrial applications) designed to work with the STM32 Nucleo kits. The module is based on a single high-side switch IPS1025H, which allows you to control devices with a current up to 2.5 A.
The board is connected to the STM32 Nucleo microcontroller through 5 kV optocouplers controlled by GPIO pins through Arduino UNO R3 and ST morpho connectors (not mounted). It works with the NUCLEO-F401RE or NUCLEO-G431RB kits, and can also be stacked with other modules, such as X-NUCLEO-OUT05A1, e.g. the system with four X-NUCLEO-OUT05A1 expansion cards enables the construction of a four-channel digital output module.
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
STM32 Nucleo development board for STM32 F4 series - with STM32F401RE MCU, 512KB flash memory, STM, RoHS
No product available!
NUCLEO series starter kit equipped with STM32G431RB microcontroller (128 kB Flash, Cortex-M4), with built-in programmer-debugger ST-Link-V3E, equipped with connectors compatible with Arduino.
An expansion board with digital outputs (for industrial applications) designed to work with the STM32 Nucleo kits. The module is based on the IPS161HF double high-side switch. STMicroelectronics X-NUCLEO-OUT10A1
Board with digital outputs designed to work with STM32 Nucleo. It is based on the IPS1025HF single high-side switch arrangement. STMicroelectronics X-NUCLEO-OUT15A1
The X-NUCLEO-IKS02A1 industrial motion MEMS sensor expansion board is compatible with the Arduino UNO R3 connector layout. STMicroelectronics X-NUCLEO-IKS02A1
No product available!
Expansion board compatible with STM32 Nucleo. Allows you to prototype solutions with digital microphones. STMicroelectronics X-NUCLEO-CCA02M2
The set consists of the STM32 NUCLEO-F401RE board with the STM32F401RE microcontroller and the X-NUCLEO-53L5A1 board with the VL53L5CX ToF distance sensor. STMicroelectronics P-NUCLEO-53L5A1
X-NUCLEO-IDS01A5 is a development board STM32 Nucleo that allows you to use the RF SPSGRF-915 module on the ISM band (915 MHz carrier).
No product available!
The X-NUCLEO-IHM17M1 is a low voltage three-phase brushless DC motor driver expansion board based on the STSPIN233 for STM32 Nucleo. It provides an affordable and easy-to-use solution for the implementation of portable motor driving applications such as thermal printers, robotics and toys
Expansion board for STM32 Nucleo designed for applications using MEMS analog microphones. The board is compatible with STM32 Nucleo and Arduino UNO R3 connectors. STMicroelectronics X-NUCLEO-AMICAM1
No product available!
P-NUCLEO-IOD02A1 is an STM32 Nucleo kit consisting of NUCLEO-L452RE (IO-Link stack), X-NUCLEO-IOD02A1 (IO-Link physical layer) and X-NUCLEO-IKS02A1 (sensor module). The kit constitutes a full IO-Link device. P-NUCLEO-IOD02A1
Expansion board with a distance sensor ToF VL53L5CX with a matrix of 64 pixels and a range of up to 4 m. The shield is compatible with STM32 Nucleo boards. STMicroelectronics X-NUCLEO-53L5A1
The X-NUCLEO-53L0A1 expansion board features the VL53L0X ranging and gesture detection sensor, based on ST’s FlightSense™, Time-of-Flight technology. It is an evaluation board that provides an introduction to the ranging and gesture detection capabilities of the VL53L0X module
No product available!
The STEVAL-FKI868V2 evaluation board is based on the S2-LP sub-1GHz ultra-low power low data-rate transceiver suitable for ISM bands and wireless M-Bus. The NUCLEO-L053R8 motherboard is equipped with an STM32L0 low power microcontroller to control the S2-LP
An expansion board designed for the STM32 Nucleo based on the Teseo-VIC3DA, a global navigation satellite system (GNSS) chip. STMicroelectronics X-NUCLEO-GNSS2A1
Expansion module designed for STM32 Nucleo-64 boards with built-in Power Delivery peripheral (UCPD). It allows prototyping of devices using the TCPP03-M20 system and USB type C in the DRP (Dual Role Power) and DRD (Dual Role Data) functions. STMicroelectronics X-NUCLEO-DRP1M1
Expansion module with color sensor VD6283. The cap is compatible with STM32 Nucleo boards. STMicroelectronics X-NUCLEO-6283A1
An expansion board with digital outputs (for industrial applications) designed to work with the STM32 Nucleo kits. The module is based on the IPS161HF double high-side switch. STMicroelectronics X-NUCLEO-OUT10A1
Extension board X-NUCLEO-IHM04A1 for STM32 Nucleo, with dual brush motor controller, operating based on the L6206 system
The set consists of the STM32 NUCLEO-F401RE board with the STM32F401RE microcontroller and the X-NUCLEO-53L1A2 board with the VL53L1 distance sensors operating in ToF technology. STMicroelectronics P-NUCLEO-53L1A2
Board with digital outputs designed to work with STM32 Nucleo. It is based on the IPS1025H single high-side switch circuit. STMicroelectronics X-NUCLEO-OUT05A1