ADXL343 + ADT7410 Sensor FeatherWing - module with 3-axis accelerometer and temperature sensor for Feather

This module allows you to add MIDI input and output to your Feather board, utilizing DIN-5 connectors and a built-in 3V optocoupler for secure 3.3V communication. The module also features LEDs to indicate data transmission and optional 3.5mm TRS MIDI sockets for the TRS MIDI A standard. It communicates via a hardware UART set to 31250 baud, allowing for easy integration with Adafruit 4740 MIDI instruments and controllers.

7-segment display controller, allowing communication over the I2C bus. Allows you to limit the pins needed to control the display. Adafruit 3088

The adapter allows the Teensy 3.x family to be similar to the Feather family tiles. Thanks to this, it is possible to use a wide range of extensions for Feather tiles. Adafruit 3200

OLED display with a diagonal of 1.3" and a resolution of 128x64 pixels. Designed for use with Feather series plates. Adafruit 4650

Data logger dedicated to Feather plates. Equipped with RTC clock, battery slot and micro SD card slot. Adafruit 2922

A module that allows you to create your own layout based on the Feather tile. Equipped with prototype holes and a set of screw connectors with pins out. Adafruit 2926

DS3231 Precision RTC FeatherWing adds an extremely accurate I2C-integrated Real Time Clock (RTC) with a Temperature Compensated Crystal Oscillator (TCXO) to any Feather main board. Adafruit 3028

Module with monostable relay. It allows you to control high-power elements with a microcontroller. Adafruit 2895

An extension that allows you to connect classic 3.5" and 5.25" floppy drives to Feather boards, allowing you to read and write data using the original interface. A built-in logic level converter ensures safe operation with 5V devices, and compatibility with the Feather M4 and RP2040 ensures adequate performance when streaming data. Adafruit 5679

A versatile extension for Adafruit Feather boards, allowing you to quickly connect Grove modules and Stemma QT accessories without soldering. The module offers three Grove A/D connectors, one UART, and two I2C connectors, making it easy to expand your project with a variety of sensors and interfaces. An additional Stemma QT port allows for further expansion of I2C devices. Adafruit 5862

This compact development board allows direct connection to 24-pin e-paper displays, ideal for energy-efficient visual projects. Equipped with a 133MHz RP2040 microcontroller, 264KB SRAM, and 8MB Flash, it offers smooth display caching and support for a wide range of peripherals. It features a dedicated SPI display interface, a STEMMA QT connector, a Li-Po charger, USB-C, and a comprehensive GPIO set with PWM, ADC, and I2C, SPI, and UART communication. Adafruit 5727

The pad for use with shallow Feather series contains two TB6612 chips that allow you to control DC motors or stepper motors. The I2C interface is used to communicate with the overlay. Adafruit 2927

Module with a matrix LED RGB 6x12 display (72 LEDs) designed to work with Feather plates. It communicates via a two-wire SPI interface. Adafruit 3449

Data logger dedicated to Thing Plus tiles. It allows you to save data on a microSD card with the possibility of reading through the USB port. Supports cards up to 32 GB. SparkFun DEV-19217

The Qwiic connector overlay provides an easy-to-install way to add Qwiic connectors to Thing Plus and Feather boards. Communication takes place via the I2C interface. Sparkfun DEV-16790

Module with 9-axis IMU LSM9DS1 system dedicated to ESP Thing board. Equipped with a connector for connecting GPS and a microSD slot. SparkFun DEV-14430