Adafruit LoRa Radio FeatherWing - RFM95W 900 MHz - radio module

An expansion board for Feather boards, featuring a 1.3-inch 128x64 monochrome OLED display and three user buttons. The board comes fully assembled and communicates via I2C, allowing for easy connection to other STEMMA QT devices. The SH1107 display provides high contrast with low power consumption, and a built-in reset button allows for quick system restarts. Adafruit 6313

This module enables the Feather series range to be expanded with 8 12-bit PWM outputs that can be used, for example, to control servos or LED diodes. Adafruit 2928

Extension module dedicated to matrix displays with HUB75 interface. Designed for Feather RP2040, M0 and M4 series tiles. Adafruit 3036

This expansion board is designed for light and sound, cosplay, and interactive prop projects. It features a ready-made NeoPixel port with a level converter, 3W RGB LED drivers, and a Class D audio amplifier for driving 8Ω or 4Ω speakers. The built-in LIS3DH accelerometer allows for motion, impact, and tilt detection, ideal for dynamic effects. It works with a wide range of Feather boards, allowing you to quickly create advanced projects in a compact format. Adafruit 3988

7-segment display controller, allowing communication over the I2C bus. Allows you to limit the pins needed to control the display. Adafruit 3088

Module with a current and voltage sensor dedicated to Feather boards. Can measure voltage up to 26 V and current up to 3.2 A. Based on INA219 sensor, I2C communication. Adafruit 3650

FeatherWing Proto - Prototyping Add-on For All Feather Boards

This expansion board is designed for light and sound, cosplay, and interactive prop projects. It features a ready-made NeoPixel port with a level converter, 3W RGB LED drivers, and a Class D audio amplifier for driving 8Ω or 4Ω speakers. The built-in LIS3DH accelerometer allows for motion, impact, and tilt detection, ideal for dynamic effects. It works with a wide range of Feather boards, allowing you to quickly create advanced projects in a compact format. Adafruit 4145

The Qwiic connector overlay provides an easy-to-install way to add Qwiic connectors to Thing Plus and Feather boards. Communication takes place via the I2C interface. Sparkfun DEV-16790

Module with a GPS receiver based on the MTK3333 system. Dedicated to Feather plates, communicates via the UART interface. Adafruit 3133

Module with monostable relay. It allows you to control high-power elements with a microcontroller. Adafruit 2895

Feather board will let you integrate packetized radio (with the RFM69 radio) or LoRa radio (with the RFM9x\'s). These radios are good options for kilometer-range radio, and paired with one of our WiFi, cellular or Bluetooth Feathers, will let you bridge from 433/900MHz to the Internet or your mobile device. Adafruit 3230

Data logger dedicated to Thing Plus tiles. It allows you to save data on a microSD card with the possibility of reading through the USB port. Supports cards up to 32 GB. SparkFun DEV-19217

These add-ons for any Feather board will let you integrate packetized radio (with the RFM69 radio) or LoRa radio (with the RFM9x\'s). These radios are good options for kilometer-range radio, and paired with one of our WiFi, cellular or Bluetooth Feathers, will let you bridge from 433/900 MHz to the Internet or your mobile device. Adafruit 3232

This is the FeatherWing OLED: it adds a 128x32 monochrome OLED plus 3 user buttons to any Feather main board. Using our Feather Stacking Headers or Feather Female Headers you can connect a FeatherWing on top of your Feather board and let the board take flight. Adafruit 2900

Pin expander designed for Feather plates. It is equipped with three sets of female strips and holes for prototyping. Adafruit 3417