RGB Matrix Featherwing Kit - extension module for matrix displays for Feather

The expansion module (shield) is designed for Feather nRF52840 boards. It enables easy connection of 16x32, 32x32 and 64x32 matrix displays. Requires self-assembly. Adafruit 4702

This compact development board allows direct connection to 24-pin e-paper displays, ideal for energy-efficient visual projects. Equipped with a 133MHz RP2040 microcontroller, 264KB SRAM, and 8MB Flash, it offers smooth display caching and support for a wide range of peripherals. It features a dedicated SPI display interface, a STEMMA QT connector, a Li-Po charger, USB-C, and a comprehensive GPIO set with PWM, ADC, and I2C, SPI, and UART communication. Adafruit 5727

OLED display with a diagonal of 1.3" and a resolution of 128x64 pixels. Designed for use with Feather series plates. Adafruit 4650

Data logger dedicated to Feather plates. Equipped with RTC clock, battery slot and micro SD card slot. Adafruit 2922

A prototyping extension for Feather boards, allowing you to connect up to three additional FeatherWings simultaneously without using stacked connectors. The board offers three pins for each Feather pin, shared 3.3V and GND power lines, and a prototyping area with a grid of holes for adding your own components. Compatible with all Feathers, it\'s ideal for prototyping and expanding your projects. Adafruit 4254

FeatherWing Proto - Prototyping Add-on For All Feather Boards

This module enables the Feather series range to be expanded with 8 12-bit PWM outputs that can be used, for example, to control servos or LED diodes. Adafruit 2928

Module with 9-axis IMU LSM9DS1 system dedicated to ESP Thing board. Equipped with a connector for connecting GPS and a microSD slot. SparkFun DEV-14430

A module that allows you to create your own layout based on the Feather tile. Equipped with prototype holes and a set of screw connectors with pins out. Adafruit 2926

CAN controller module for Feather boards. It features an MCP2515 CAN controller and a TJA1051 transceiver and allows data transfer at speeds of up to 1Mb/s. Adafruit 5709

FeatherWing Doubler is a shield that allows you to create your own layout based on two or one Feather series. The plate has 256 holes, including designated, common solder points for supply voltages. Adafruit 2890

This expansion board is designed for light and sound, cosplay, and interactive prop projects. It features a ready-made NeoPixel port with a level converter, 3W RGB LED drivers, and a Class D audio amplifier for driving 8Ω or 4Ω speakers. The built-in LIS3DH accelerometer allows for motion, impact, and tilt detection, ideal for dynamic effects. It works with a wide range of Feather boards, allowing you to quickly create advanced projects in a compact format. Adafruit 4145

This expansion board is designed for light and sound, cosplay, and interactive prop projects. It features a ready-made NeoPixel port with a level converter, 3W RGB LED drivers, and a Class D audio amplifier for driving 8Ω or 4Ω speakers. The built-in LIS3DH accelerometer allows for motion, impact, and tilt detection, ideal for dynamic effects. It works with a wide range of Feather boards, allowing you to quickly create advanced projects in a compact format. Adafruit 3988

The compact enclosure for the Adafruit Feather RP2040 with DVI output is printed using SLA technology in semi-transparent plastic, providing protection and visibility of the LED indicators. It allows easy access to all ports and buttons, and the snap-in design eliminates the need for screws or glue. Adafruit 6241

Cap for use with shallow Feather series, with radio module RFM95W 900MHz. It offers a range of up to 2 kilometers (the range can be increased by using an external antenna). It has a SPI interface. Adafruit 3231

The Qwiic connector overlay provides an easy-to-install way to add Qwiic connectors to Thing Plus and Feather boards. Communication takes place via the I2C interface. Sparkfun DEV-16790