![Adafruit Feather RP2040 - board with RP2040 microcontroller](https://kamami.pl/75145-large_default/adafruit-feather-rp2040-board-with-rp2040-microcontroller-adafruit-4884.jpg)
![Adafruit Feather RP2040 - board with RP2040 microcontroller](https://kamami.pl/75145-large_default/adafruit-feather-rp2040-board-with-rp2040-microcontroller-adafruit-4884.jpg)
zł64.25 tax excl.
The board with the RP2040 microcontroller equipped with two ARM Cortex-M0+ cores, which work at a frequency of 133 MHz, 256 kB RAM. The board also has 8 MB of QSPI flash memory. The system can be programmed in C/C++ or MicroPython. Adafruit 4884
free shipping in Poland for all orders over 500 PLN
If your payment will be credited to our account by 11:00
Each consumer can return the purchased goods within 14 days
Adafruit Feather RP2040 is a board equipped with the RP2040 microcontroller designed by the Raspberry Pi foundation. The system has two ARM Cortex M0+ cores operating at a frequency of 133 MHz and 256 KB of RAM. The microcontroller is not equipped with flash memory, but on the board there is an external memory with a capacity of 8 MB connected via QSPI interface.
On the board, in addition to the RP2040 system and Flash memory, the user will find a 3.3 V voltage stabilizer, Boot and Reset buttons, LED and RGB NeoPixel diodes, a USB type C connector for powering and programming the module, and 21 GPIO outputs with such parameters. as four 12-bit ADC inputs, 16 PWM outputs, two I2C, SPI and UART interfaces.
The platform supports the popular MicroPython and C/C++ programming languages. Programs can be loaded to the memory via the USB interface using the built-in UF2 bootloader or an external programmer via the SWD interface.
Cable with USB typ A and USB typ C connectors, cable length 0.5 m. LANBERG
Cable with USB typ A and USB typ C connectors, cable length 1 m. LANBERG CA-USBO-10CC-0010-BK
Cable with USB typ A and USB typ C connectors, cable length 1,8 m. LANBERG CA-USBO-10CC-0018-BK
Module with ATmega32u4 microcontroller and 900 MHz wireless transceiver. The module can be used for transmission in the ISM 868 MHz band after the appropriate software configuration. The microcontroller is clocked at 8 MHz and works at 3.3 V. Adafruit 3076
No product available!
Module with a current and voltage sensor dedicated to Feather boards. Can measure voltage up to 26 V and current up to 3.2 A. Based on INA219 sensor, I2C communication. Adafruit 3650
Module with a matrix LED RGB 6x12 display (72 LEDs) designed to work with Feather plates. It communicates via a two-wire SPI interface. Adafruit 3449
The board with the RP2040 microcontroller equipped with two ARM Cortex-M0+ cores, which work at a frequency of 133 MHz, 256 kB RAM. The board also has 4 MB of QSPI flash memory. The system can be programmed in C/C++ or MicroPython. Adafruit 4888
Feather board will let you integrate packetized radio (with the RFM69 radio) or LoRa radio (with the RFM9x\'s). These radios are good options for kilometer-range radio, and paired with one of our WiFi, cellular or Bluetooth Feathers, will let you bridge from 433/900MHz to the Internet or your mobile device. Adafruit 3230
At the Feather M0\'s heart is an ATSAMD21G18 ARM Cortex M0 processor, clocked at 48 MHz and at 3.3V logic, the same one used in the new Arduino Zero. This chip has a whopping 256K of FLASH (8x more than the Atmega328 or 32u4) and 32K of RAM (16x as much). Adafruit 2796
Cap for use with shallow Feather series, with radio module RFM95W 900MHz. It offers a range of up to 2 kilometers (the range can be increased by using an external antenna). It has a SPI interface. Adafruit 3231
This is the FeatherWing OLED: it adds a 128x32 monochrome OLED plus 3 user buttons to any Feather main board. Using our Feather Stacking Headers or Feather Female Headers you can connect a FeatherWing on top of your Feather board and let the board take flight. Adafruit 2900
No product available!
Development board with ESP8266 microcontroller with built-in Wi-Fi communication. The system is clocked at 80 MHz and powered by 3.3 V. It includes a Tensillica core and a full Wi-Fi stack. Adafruit 3046
Low-power, 2.4GHz spectrum wireless protocol that you can use with iOS without needing special certification. Supported by all modern smart phones - excellent for use in portable projects that will make use of an iOS or Android phone or tablet; it also is supported in Mac OS X and Windows 8+. Adafruit 2995
The adapter allows the Teensy 3.x family to be similar to the Feather family tiles. Thanks to this, it is possible to use a wide range of extensions for Feather tiles. Adafruit 3200
No product available!
At the Feather M0\'s heart is an ATSAMD21G18 ARM Cortex M0 processor, clocked at 48 MHz and at 3.3V logic, the same one used in the new Arduino Zero. This chip has a whopping 256K of FLASH (8x more than the Atmega328 or 32u4) and 32K of RAM (16x as much)! This chip comes with built in USB so it has USB-to-Serial program & debug capability built in with no need for an FTDI-like chip. Adafruit 3179
No product available!
Pin expander designed for Feather plates. It is equipped with three sets of female strips and holes for prototyping. Adafruit 3417
The board with the RP2040 microcontroller equipped with two ARM Cortex-M0 + cores, which work at a frequency of 133 MHz, 256 kB RAM. The board also has 16 MB of QSPI flash memory. The system can be programmed in C/C++ or microPython. SparkFun DEV-17745
A module that allows you to create your own layout based on the Feather tile. Equipped with prototype holes and a set of screw connectors with pins out. Adafruit 2926
Adafruit Feather M0 WiFi with uFL - ATSAMD21 + ATWINC1500 is a development board with a 32-bit ATSAMD21G18 microcontroller based on Cortex-M0 core. The board also has an ATWINC1500 module that provides WiFi connectivity. Adafruit 3061
No product available!
The board with the RP2040 microcontroller equipped with two ARM Cortex-M0+ cores, which work at a frequency of 133 MHz, 256 kB RAM. The board also has 8 MB of QSPI flash memory. The system can be programmed in C/C++ or MicroPython. Adafruit 4884