Adafruit Feather 328P - development board with Atmel 328P microcontroller (3.3V, 8MHz)
ID: 569851
5906623429738
zł73.70
Tax included
zł59.92 tax excl.
Adafruit Feather 328P is a module with a built-in ATmega 328P AVR microcontroller (8MHz, 32kB Flash, 2kB RAM). The board is compatible with Arduino IDE, has small dimensions and low weight, and the built-in USB connector allows programming and debugging. Adafruit 3458
Description
Adafruit Feather 328P is a module with a built-in ATmega 328P AVR microcontroller clocked at 8 MHz. The built-in system works with 3.3 V logic, has a flash memory with a capacity of 32 kB and 2 kB of RAM. The board is compatible with the Arduino IDE environment, and the USB connector allows its programming and debugging. In addition, the built-in Li-Pol battery connector allows you to power the board and charge the cell via USB. Battery voltage can be measured through the analog input of the microcontroller, thanks to which the device gains mobility and can signal the need to connect to USB for charging.
properties
- Built-in ATmega 328P AVR microcontroller (8 MHz, 32 kB Flash, 2 kB RAM, 3.3 V logic)
- Built-in 3.3 V voltage stabilizer with a maximum current capacity of 500 mA
- system programmed with Arduino bootloader, debugging option
- USB <> UART converter (CP2104 chip)
- 19 GPIO lines
- Hardware support I2C, SPI
- 6 PWM lines
- 8 analog inputs (2 lines shared with the I2C interface)
- Built-in Li-Po charger with charging indicator (maximum 100 mA charging current)
- The red light-emitting diode connected to the line No. 13
- Power supply control line
- Built-in microcontroller reset button
- Four mounting holes
- Board dimensions: 51 mm x 23 mm x 8 mm
- Weight: 4.8 g
Attention! The microcontroller lines tolerate the 3.3V voltage. Applying higher voltage to these lines can damage the microcontroller.
Included
- Adafruit Feather 328P tile
- Pin connectors (short) for self-assembly
569851
Data sheet
- Microcontroller
- ATmega328P
- Flash memory
- 32kB
- Number of I/O
- 19
- Ethernet
- none
- WiFi/BT module
- No
- Bluetooth module
- No
- MicroSD slot
- No
- Length
- 51mm
- Width
- 23 mm
- USB connector type
- microUSB type B
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
Plate from the Adafruit Feather series equipped with an ATmega32u4 microcontroller and a small prototype surface (5x7). The chip contains 32KB flash memory, 2KB RAM memory and built-in USB support. The plate is compatible with Arduino. Adafruit 2771
zł117.62
24h
Available quantity: 2
Available
Bluetooth Low Energy, 2.4GHz spectrum wireless protocol. Excellent for use in portable projects that will make use of an iOS or Android phone or tablet. It also is supported in Mac OS X and Windows 8+. Adafruit 2829
zł176.59
24h
Available quantity: 2
Available
Adafruit FeatherWing module with snap relay. It allows you to control high-power components using a microcontroller. It allows switching current to 2A (at 40VAC or 30VDC) and voltage up to 250VAC. Adafruit 2923
zł40.74
24h
Available quantity: 1
Available
At the Feather 32u4\'s heart is ATmega32u4 clocked at 8 MHz and at 3.3V logic. This chip has 32K of flash and 2K of RAM, with built in USB so not only does it have a USB-to-Serial program & debug capability built in with no need for an FTDI-like chip, it can also act like a mouse, keyboard, USB MIDI device, etc. Adafruit 2795
zł143.57
24h
Available quantity: 1
Available
Other products in the same category (16)
Development kit with SAMD21G18 microcontroller with ARM Cortex M0 core and LoRa RFM95 868/915 MHz radio communication module. Adafruit 3178
zł176.16
24h
Available quantity: 1
Available
Development kit with nRF52840 microcontroller with ARM Cortex M4F core and BLE communication. Equipped with motion sensors, magnetometer, light, humidity, pressure sensors and a microphone. Adafruit 4516
zł245.41
4 weeks
No product available!
Module with WiFi and BLE Espressif ESP32-S3. It integrates a LiPo charging circuit and an RGB diode. It is equipped with a STEMMA QT connector. Adafruit 5477
zł90.95
24h
Available quantity: 3
Available
Adafruit HUZZAH32 is a development board with a built-in WiFi ESP32 module. Processor frequency: 240 MHz, Li-Pol battery charging system. The board has soldered goldpin connectors. Adafruit 3591
zł152.38
4 weeks
No product available!
At the Feather M0\'s heart is an ATSAMD21G18 ARM Cortex M0 processor, clocked at 48 MHz and at 3.3V logic. 256K FLASH, 32K RAM, built in USB and battery charging. Adafruit 2772
zł116.17
24h
Available quantity: 1
Available
The board is equipped with the ATSAMD51J19 microcontroller with ARM Cortex-M4 core and SPI Flash memory, GPIO pins, connector for connecting the battery with the charging circuit. Adafruit 3857
zł119.31
24h
Available quantity: 1
Available
Adafruit Feather M0 WiFi with uFL - ATSAMD21 + ATWINC1500 is a development board with a 32-bit ATSAMD21G18 microcontroller based on Cortex-M0 core. The board also has an ATWINC1500 module that provides WiFi connectivity. Adafruit 3061
zł206.07
4 weeks
No product available!
Adafruit HUZZAH32 is a development board with a built-in WiFi ESP32 module. Processor frequency: 240 MHz, the module has a built-in system for charging Li-Pol batteries. The plate has soldered goldpin connectors (female extension). Adafruit 3619
zł157.76
4 weeks
No product available!
Adafruit Feather M0 Express - Designed for CircuitPython is a development board with a 32-bit ATSAMD21G18 microcontroller based on the Cortex-M0 core. The board works with CircuitPython, which allows you to program the MicroPython language. Adafruit 3403
zł111.97
24h
Available quantity: 2
Available
Board with RP2040 microcontroller and class D mono audio amplifier based on MAX98357 chip. It has a built-in LIS3DH three-axis accelerometer, an RGB NeoPixel LED, a LiPo charging circuit, and a STEMMA QT connector. Adafruit 5768
zł122.47
24h
Available quantity: 7
Available
The board is equipped with ATSAME51 microcontroller (ARM Cortex-M core) with CAN bus and SPI Flash memory, GPIO pins and a connector for connecting the battery with the charging circuit. Adafruit 4759
zł143.34
24h
Available quantity: 3
Available
A modern development board in the Feather format, equipped with a dual-core Raspberry Pi RP2350 Cortex M33 microcontroller clocked at 150 MHz and 8 MB of PSRAM, ideal for advanced IoT projects and Micropython/CircuitPython applications. The board offers a wide range of ports, including an HSTX 22-pin connector, USB-C with bootloader, and STEMMA QT, as well as numerous GPIOs and an integrated LiPo battery charger, combining high performance with convenience of use. Adafruit 6130
zł78.54
24h
Available quantity: 1
Available
A board with an RP2040 microcontroller and a LoRa RF95 module operating in the 868 MHz frequency band. It has a built-in LiPo charging circuit and STEMMA QT connector. Ideal for IoT projects. Adafruit 5714
zł175.46
24h
Available quantity: 2
Available
Module with WiFi Espressif ESP32. It offers 8MB Flash, 2MB PSRAM, LiPo charging circuit and RGB LED. It is equipped with a STEMMA QT connector. Adafruit 5438
zł102.85
24h
Available quantity: 1
Available
Module with WiFi and BLE Espressif ESP32-S3 system and LCD TFT display. It integrates a LiPo charging circuit and an RGB diode. It is equipped with a STEMMA QT connector. Adafruit 5483
zł155.03
24h
Available quantity: 4
Available
A compact development board with a built-in 1.14" IPS display, ideal for user interfaces, IoT projects, and case-mounted devices. Featuring the ESP32-S3 with Wi-Fi, Bluetooth LE, and native USB, it offers 4MB of Flash and 2MB of PSRAM to support more advanced graphics and networking applications. Three user buttons, a STEMMA QT connector, and an integrated LiPo charger provide convenient prototyping and expansion capabilities. Adafruit 6303
zł125.84
24h
Available quantity: 1
Available
Adafruit Feather 328P is a module with a built-in ATmega 328P AVR microcontroller (8MHz, 32kB Flash, 2kB RAM). The board is compatible with Arduino IDE, has small dimensions and low weight, and the built-in USB connector allows programming and debugging. Adafruit 3458