FeatherWing Tripler Mini Kit - pin expander for Feather
ID: 564093
5906623429516
zł47.29
Tax included
zł38.45 tax excl.
Pin expander designed for Feather plates. It is equipped with three sets of female strips and holes for prototyping. Adafruit 3417
Description
Pin expander designed for Feather boards. It is equipped with three standard female connectors for direct module connection, which also enable the connection of additional expansion boards. The holes with a raster of 2.54 mm and the connected 3.3 V and GND pins make prototyping much easier. Full documentation is available on the product page.
Features
- 3 x Standard Feather Female Connector
- Interconnected pins 3.3 V and GND
- Dimensions: 71.25 x 51 x 12 mm
Kit contains
- FeatherWing Tripler Mini
- 3 x set of female goldpin connectors
564093
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
Plate from the Adafruit Feather series equipped with an ATmega32u4 microcontroller and a small prototype surface (5x7). The chip contains 32KB flash memory, 2KB RAM memory and built-in USB support. The plate is compatible with Arduino. Adafruit 2771
zł117.62
24h
Available quantity: 2
Available
FeatherWing Doubler is a shield that allows you to create your own layout based on two or one Feather series. The plate has 256 holes, including designated, common solder points for supply voltages. Adafruit 2890
zł42.83
24h
Available quantity: 1
Available
At the Feather M0\'s heart is an ATSAMD21G18 ARM Cortex M0 processor, clocked at 48 MHz and at 3.3V logic, the same one used in the new Arduino Zero. This chip has a whopping 256K of FLASH (8x more than the Atmega328 or 32u4) and 32K of RAM (16x as much). Adafruit 2796
zł137.85
24h
Available quantity: 1
Available
This module enables the Feather series range to be expanded with 8 12-bit PWM outputs that can be used, for example, to control servos or LED diodes. Adafruit 2928
zł55.40
24h
Available quantity: 1
Available
7-segment display controller, allowing communication over the I2C bus. Allows you to limit the pins needed to control the display. Adafruit 3088
zł52.00
24h
Available quantity: 1
Available
Other products in the same category (16)
Feather board will let you integrate packetized radio (with the RFM69 radio) or LoRa radio (with the RFM9x\'s). These radios are good options for kilometer-range radio, and paired with one of our WiFi, cellular or Bluetooth Feathers, will let you bridge from 433/900MHz to the Internet or your mobile device. Adafruit 3230
zł53.91
24h
Available quantity: 1
Available
The compact enclosure for the Adafruit Feather RP2040 with DVI output is printed using SLA technology in semi-transparent plastic, providing protection and visibility of the LED indicators. It allows easy access to all ports and buttons, and the snap-in design eliminates the need for screws or glue. Adafruit 6241
zł23.64
24h
Available quantity: 3
Available
Module with a GPS receiver based on the MTK3333 system. Dedicated to Feather plates, communicates via the UART interface. Adafruit 3133
zł183.10
24h
Available quantity: 1
Available
The pad for use with shallow Feather series contains two TB6612 chips that allow you to control DC motors or stepper motors. The I2C interface is used to communicate with the overlay. Adafruit 2927
zł113.25
24h
Available quantity: 3
Available
The adapter allows the Teensy 3.x family to be similar to the Feather family tiles. Thanks to this, it is possible to use a wide range of extensions for Feather tiles. Adafruit 3200
zł38.92
4 weeks
No product available!
7-segment display controller, allowing communication over the I2C bus. Allows you to limit the pins needed to control the display. Adafruit 3088
zł52.00
24h
Available quantity: 1
Available
CAN controller module for Feather boards. It features an MCP2515 CAN controller and a TJA1051 transceiver and allows data transfer at speeds of up to 1Mb/s. Adafruit 5709
zł66.67
24h
Available quantity: 2
Available
Cap for use with shallow Feather series, with radio module RFM95W 900MHz. It offers a range of up to 2 kilometers (the range can be increased by using an external antenna). It has a SPI interface. Adafruit 3231
zł113.66
24h
Available quantity: 2
Available
Gamepad module (game controller) with joystick and buttons. Designed for Feather tiles. Adafruit 3632
zł65.98
24h
Available quantity: 1
Available
Module with a matrix LED RGB 6x12 display (72 LEDs) designed to work with Feather plates. It communicates via a two-wire SPI interface. Adafruit 3449
zł176.59
24h
Available quantity: 2
Available
Module with a current and voltage sensor dedicated to Feather boards. Can measure voltage up to 26 V and current up to 3.2 A. Based on INA219 sensor, I2C communication. Adafruit 3650
zł44.90
24h
Available quantity: 2
Available
Data logger dedicated to Feather plates. Equipped with RTC clock, battery slot and micro SD card slot. Adafruit 2922
zł47.17
24h
Available quantity: 1
Available
OLED display with a diagonal of 1.3" and a resolution of 128x64 pixels. Designed for use with Feather series plates. Adafruit 4650
zł84.24
24h
Available quantity: 1
Available
Module with monostable relay. It allows you to control high-power elements with a microcontroller. Adafruit 3191
zł49.73
24h
Available quantity: 1
Available
Module with 9-axis IMU LSM9DS1 system dedicated to ESP Thing board. Equipped with a connector for connecting GPS and a microSD slot. SparkFun DEV-14430
zł117.93
24h
Available quantity: 2
Available
FeatherWing Proto - Prototyping Add-on For All Feather Boards
zł27.02
24h
Available quantity: 2
Available
Pin expander designed for Feather plates. It is equipped with three sets of female strips and holes for prototyping. Adafruit 3417