

A module that allows you to create your own layout based on the Feather tile. Equipped with prototype holes with a pitch of 2.54 mm (including designated soldering points for power and I2C) and a set of screw connectors with pins out. Full documentation with examples is available on the product page.
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Plate from the Adafruit Feather series equipped with an ATmega32u4 microcontroller and a small prototype surface (5x7). The chip contains 32KB flash memory, 2KB RAM memory and built-in USB support. The plate is compatible with Arduino. Adafruit 2771
FeatherWing Proto - Prototyping Add-on For All Feather Boards
At the Feather M0\'s heart is an ATSAMD21G18 ARM Cortex M0 processor, clocked at 48 MHz and at 3.3V logic. 256K FLASH, 32K RAM, built in USB and battery charging. Adafruit 2772
Low-power, 2.4GHz spectrum wireless protocol that you can use with iOS without needing special certification. Supported by all modern smart phones - excellent for use in portable projects that will make use of an iOS or Android phone or tablet; it also is supported in Mac OS X and Windows 8+. Adafruit 2995
Module with a matrix LED RGB 6x12 display (72 LEDs) designed to work with Feather plates. It communicates via a two-wire SPI interface. Adafruit 3449
Data logger dedicated to Thing Plus tiles. It allows you to save data on a microSD card with the possibility of reading through the USB port. Supports cards up to 32 GB. SparkFun DEV-19217
Module with 3-axis accelerometer ADXL343 and precise temperature sensor ADT7410 dedicated to Feather series boards. Equipped with a STEMMA QT connector, it communicates via the I2C interface. Adafruit 4147
7-segment display controller, allowing communication over the I2C bus. Allows you to limit the pins needed to control the display. Adafruit 3088
Module with monostable relay. It allows you to control high-power elements with a microcontroller. Adafruit 3191
This is the FeatherWing OLED: it adds a 128x32 monochrome OLED plus 3 user buttons to any Feather main board. Using our Feather Stacking Headers or Feather Female Headers you can connect a FeatherWing on top of your Feather board and let the board take flight. Adafruit 2900
Module with 9-axis IMU LSM9DS1 system dedicated to ESP Thing board. Equipped with a connector for connecting GPS and a microSD slot. SparkFun DEV-14430
Module with a GPS receiver based on the MTK3333 system. Dedicated to Feather plates, communicates via the UART interface. Adafruit 3133
The adapter allows the Teensy 3.x family to be similar to the Feather family tiles. Thanks to this, it is possible to use a wide range of extensions for Feather tiles. Adafruit 3200
No product available!
These add-ons for any Feather board will let you integrate packetized radio (with the RFM69 radio) or LoRa radio (with the RFM9x\'s). These radios are good options for kilometer-range radio, and paired with one of our WiFi, cellular or Bluetooth Feathers, will let you bridge from 433/900 MHz to the Internet or your mobile device. Adafruit 3232
The compact enclosure for the Adafruit Feather RP2040 with DVI output is printed using SLA technology in semi-transparent plastic, providing protection and visibility of the LED indicators. It allows easy access to all ports and buttons, and the snap-in design eliminates the need for screws or glue. Adafruit 6241
The expansion module (shield) is designed for Feather nRF52840 boards. It enables easy connection of 16x32, 32x32 and 64x32 matrix displays. Requires self-assembly. Adafruit 4702
CAN controller module for Feather boards. It features an MCP2515 CAN controller and a TJA1051 transceiver and allows data transfer at speeds of up to 1Mb/s. Adafruit 5709
Extension module dedicated to matrix displays with HUB75 interface. Designed for Feather RP2040, M0 and M4 series tiles. Adafruit 3036
Module with a current and voltage sensor dedicated to Feather boards. Can measure voltage up to 26 V and current up to 3.2 A. Based on INA219 sensor, I2C communication. Adafruit 3650
Pin expander designed for Feather plates. It is equipped with three sets of female strips and holes for prototyping. Adafruit 3417
A module that allows you to create your own layout based on the Feather tile. Equipped with prototype holes and a set of screw connectors with pins out. Adafruit 2926