Dual DC motor driver module based on TB6612FNG. The chip has two full H-bridges built-in, which means it can drive 2-4 solenoids (only two can be active at the same time, on opposite bridges), two DC motors or one stepper motor. It allows you to control drives with a voltage range of 4.5 to 13.5 V, and each channel can draw a current of 1.2 A (instantaneous 3 A). The module is controlled with PWM signals for speed control and digital outputs for direction control. It operates with voltages from 2.7 to 5 V. It will work well in small mobile robot projects and for controlling home automation components. Full documentation with examples of use is available on the product page.
Data sheet
Manufacturer
Responsible person
Bipolar stepper motor. It has a resolution of 200 steps/revolution (1.8 ° per step), has a nominal voltage of 7.4 V, and draws a current of 0.28 A per coil. Pololu 1207
DC motor set with a two-sided shaft and a matching 66mm diameter wheel with the tire. HC02-48
A set of 40 pieces of female-female connecting cables in various colors, 10 cm long
A set of 40 pcs of male-female connecting cables in various colors, 10 cm long
Dual MAX14870 Motor Driver is a dual DC driver compatible with Raspberry Pi that allows you to control two DC motors with 4.5-36V continuous current of 1.7A. Pololu 3759
ual MAX14870 Motor Driver is a dual DC motor driver compatible with the Raspberry Pi standard that allows you to control two DC motors with 4.5 ... 36V continuous current of 1.7A. Pololu 3758
This powerful motor controller makes closed-loop speed or position (but not both!) control of a brushed DC motor easy, with quick configuration over USB using our free software. It supports five control interfaces: USB, TTL serial, I²C, analog voltage (potentiometer), and hobby radio control (RC).
DC motor driver with voltage 6.5 ... 40V and maximum continuous current 13A. It has the ability to easily implement the feedback loop and numerous control interfaces. Polol 3147
DC motor driver with voltage 6.5..30V and maximum continuous current 27A. It has the ability to easily implement the feedback loop and numerous control interfaces. Polol 3148
No product available!
DC motor driver with voltage 6.5..40V and maximum continuous current 21A. It has the ability to easily implement the feedback loop and numerous control interfaces. Polol 3149
No product available!
The controller enables to supply the motors with voltage in the range of 10-47V and power consumption in continuous operation of 1.7A (4.5A peak) for each channel in dual or 3.4A mode (9A peak) in single channel mode. Pololu 2999
TB9051FTG Single Brushed The DC Motor Driver Carrier is a single DC motor driver that allows the motor to be supplied with voltage in the 4.5 ... 28V range and power consumption at a continuous 2.6 A (5A peak) operation. Pololu 2997
DC motor driver module with two channels, dedicated to use in modeling. It can be controlled by an RC transmitter and uses the PPM signal. DFRobot DFR0513
The expansion module is designed to work with micro:bit. It allows you to control 4 DC motors or two stepper motors and 8 servos. It communicates via the I2C interface. DFRobot DFR0548
Dual DC motor controller designed for Arduino, which enables the motor to be supplied with voltage in the 4.5 ... 28V range and power consumption in continuous operation of 2.6 A (5A at the top) of two DC motors. Polol 2520
Dual DC motor controller designed for Raspberry Pi, which enables the engine to be supplied with voltage in the 4.5-28V range and power consumption in continuous operation of 2.6A (5A in peak) of two DC motors. Pololu 2762
Dual DC motor controller designed for Raspberry Pi, which enables the engine to be supplied with voltage in the 4.5-28V range and power consumption in continuous operation of 2.6A (5A in peak) of two DC motors. Self-assembly set. Pololu 2761
DC motor driver with voltage 4.5..28V and maximum continuous current of 2.6A. It has the ability to easily implement the feedback loop and numerous control interfaces. Polol 3143
No product available!
DC motor driver with voltage 4.5..28V and maximum continuous current of 2.6A. It has the ability to easily implement the feedback loop and numerous control interfaces. Polol 3142
No product available!
Bi-directional ESC speed controller for brush motors. It can deliver 20 A and has cables terminated with an XT60 connector. DFRobot DRI0047
TB6612FNG dual DC motor controller module. It can be used as a stepper motor driver or solenoid driver. Adafruit 2448