Module with TB6612FNG DC motors dual driver. It allows you to control two DC motors with a voltage in the range from 2.5 to 13.5 V, and each channel can take a current of 1.2 A (temporary 3.2 A). Motors and power supply to the drives are connected via screw connectors, and the module is controlled by the built-in STM32 microcontroller. There is also a 4-pin connector for connecting a stepper motor. The board is equipped with a Grove connector, so it can be used with the Base Shield V2 and Arduino extension. The module communicates via the I2C interface and is supplied with the voltage of 3.3 V or 5 V. Full documentation with examples of use is available on the product page.
.jpg)
Data sheet
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Arduino Uno Rev3 is a popular board with Atmel ATmega328 microcontroller from the AVR family, there are 14 I / O lines, 6 PWM channels and 6 analog inputs. The additional ATmega16U4 microcontroller realizes communication via the USB interface. Arduino A000066
A set with ATmega2560 microcontroller (256 kB Flash, 8 kB RAM, 4 kB EEPROM) clocked at 16 MHz. The user has, among others: 54 I / O lines, 14 PWM channels, 16 analog inputs. Arduino A000067
No product available!
Base Shield V2 is an extension for tiles with an Arduino shield connector, it has a Grove connector, which can be connected to Grove-compatible modules / sensors. Seeedstudio 103030000
Module with a 16-channel PWM PCA9685 driver. The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 108020102
No product available!
The expansion module is designed for Arduino Mega and Google ADK boards. It is equipped with connectors to which you can attach modules compatible with the Grove standard. Seeed Studio 103020027
A small servo (23 x 11.5 x 24 mm) with a weight of 8.6 g, power supply 4.8-6V, maximum torque 1.8 kg / cm (at 6V). It has a connector compatible with the Grove standard. Seeed Studio 316010005
MH-Z16 carbon dioxide sensor with Grove connector. It communicates via the UART interface. Seeed Studio 101020067
Speech recognition module with Nuvoton ISD9160 system, microphone, Flash memory and speaker output. The board is equipped with a Grove connector and communicates via the UART interface. Seeed Studio 101020232
Recorder v3.0 is a module that allows you to record and play sounds. The module was based on the ISD9160FI system, it also has a FLASH memory with a capacity of 2 MB, which allows for recording up to 83 seconds long. The set contains a small loudspeaker on which recorded sounds can be played. Seeed studio 107020029
Module with a reflection sensor (line sensor) RS-06WD. The board is equipped with a Grove connector and communicates via a digital interface. Seeed Studio 101020172
The module allows the detection of volatile organic compounds (VOC) in the air, based on Winsen\'s WSP2110 system. Allows for detection in the air; formaldehyde (HCHO), methane, benzene, toluene, alcohol, etc. The sensor output is an analog signal. Seeed studio 101020001
Module with LoRa transmitter based on RFM95 (SX1276 LoRa®). It works with a frequency of 433 MHz, maximum power up to 100 mW and a power gain of up to + 20dBm. The module has a built-in antenna, but it is possible to connect an external antenna (MHF connector). The module has a connector in accordance with the Grove standard. Seeed studio 113060007
Module with a pulse sensor (heart rate). The board is equipped with a Grove connector and a digital output in the form of pulses. Seeed Studio 101020033
No product available!
Base Shield V2 is an extension for tiles with an Arduino shield connector, it has a Grove connector, which can be connected to Grove-compatible modules / sensors. Seeedstudio 103030000
3-port I2C splitter module. The board is equipped with Grove connectors and allows you to connect additional I2C devices. Seeed Studio 103020006
Module with a voltage divider. Equipped with a Grove connector, it allows the input voltage to be reduced by 3 or 10 times. Seeed Studio 104020000
No product available!
Base plate designed for NodeMCU (ESP8266 WIFI). The module is an expansion board that allows you to plug the NodeMCU into the slot and use the Grove sensor ports. Seeed Studio 105020008
Universal module for prototyping. It has 58 prototype fields and a Grove connector. Seeed Studio 101020035
Grove adapter for 3.5mm screw connector. Seeed Studio 103020007
Set (5 pieces) of wires for attaching modeling servos with the Grove system. With one wire you can connect 2 servos to one Grove slot. Seeed studio 110990057
GrovePi + is an extension in the form of a HAT overlay intended for Raspberry Pi computers (B / B + / A + / 2/3/3 +). The module has 15 connectors to which modules / sensors compatible with the Grove standard can be connected. Seeed Studio 103010002
Module with TB6612FNG DC motors dual driver. The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 108020103