.png)
Water atomizer - Grove module
ID: 564199
5906623414123
zł40.16
Tax included
zł32.65 tax excl.
The kit includes a control module (with ETA1617 and NE555) and an ultrasonic transducer. The water atomiser module allows for the construction of, for example, a small humidifier. The module has a connector in accordance with the Grove standard. Seeed studio 101020090
Description
The kit includes a control module (with ETA1617 and NE555) and an ultrasonic transducer. The water atomiser module allows for the construction of, for example, a small humidifier. It can also be used for other projects where atomization (spraying) is needed. The module has a connector in accordance with the Grove standard.
The module can be used with the Base Shield V2 - shield extension with Grove connectors for Arduino
Attention!
Do not touch the contacts to which the ultrasound transducer is connected (marked with a red frame in the picture above) because the voltage (momentary) up to 65 V may occur on them, in addition the area heats up during operation.
Do not touch the contacts to which the ultrasound transducer is connected (marked with a red frame in the picture above) because the voltage (momentary) up to 65 V may occur on them, in addition the area heats up during operation.
properties
- Based on the following systems: ETA1617, NE555
- Maximum power: 2 W
- Peak output voltage: 65 ± 5 V
- Operating frequency: 105 ± 5 kHz
- Grove connector
- Power supply: 5 V
Included
- Water atomizer - Grove module
- Ultrasonic transducer
- Grove system cable
564199
Manufacturer
- BTC Korporacja sp. z o. o.
- Ludwinowo Zegrzyńskie 52G
- 05-140 Ludwinowo Zegrzyńskie
- Poland
- [email protected]
- 22 767 36 20
Responsible person
- BTC Korporacja sp. z o. o.
- Ludwinowo Zegrzyńskie 52G
- 05-140 Ludwinowo Zegrzyńskie
- Poland
- [email protected]
- 22 767 36 20
You might also like
A small module with a temperature sensor (thermistor). As the temperature changes, the resistance of the thermistor changes, which allows the temperature to be measured in the range from -40 to 125 ° C with an accuracy of 1.5 ° C. The module has a connector in accordance with the Grove standard. Seeed studio 101020015
zł13.76
24h
Available quantity: 2
Available
Module with a flame sensor or other light sources with a wavelength in the range of 760 to 1100 nm. It was based on the YG1006 sensor (photovolver NPN). The sensor has a connector compatible with the Grove standard. Seeed studio 101020049
zł38.14
24h
Available quantity: 2
Available
The module allows the detection of volatile organic compounds (VOC) in the air, based on Winsen\'s WSP2110 system. Allows for detection in the air; formaldehyde (HCHO), methane, benzene, toluene, alcohol, etc. The sensor output is an analog signal. Seeed studio 101020001
zł79.32
24h
Available quantity: 4
Available
Base Shield V2 is an extension for tiles with an Arduino shield connector, it has a Grove connector, which can be connected to Grove-compatible modules / sensors. Seeedstudio 103030000
zł24.40
24h
Available quantity: 18
Available
Other products in the same category (16)
Module with a MLX90640 thermal imaging camera with a 32x24 field matrix and a 55° viewing angle. The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 114020141
zł887.62
4 weeks
No product available!
Module with light sensor - LS06-S phototransistor. The board is equipped with a Grove connector and has an analog output. Seeed Studio 101020132
zł9.69
24h
Available quantity: 3
Available
Vertical Grove socket for through-hole mounting, 4-pin, pitch 2.0 mm. Set of 10 pieces. Seeed Studio 110990030
zł5.90
24h
Available quantity: 72
Available
Angled Grove socket for through-hole mounting, 4-pin, pitch 2.0 mm. Set of 10 pieces. Seeed Studio 110990037
zł7.13
24h
Available quantity: 76
Available
The expansion module is designed for Wio Lite tiles and compatible with Adafruit Feather. It is equipped with connectors to which you can attach modules compatible with the Grove standard. Seeed Studio 103020252
Regular pricezł30.81zł23.74
24h
Available quantity: 10
Available
Yellow mounting for Grove modules, which ensure convenient installation and replacement of modules in the project. Compatible with LEGO. Set of 4. Seeed Studio 110070025
zł7.88
24h
Available quantity: 1
Available
Module with a gas concentration sensor MQ9, which enables the detection of carbon monoxide and combustible gases (methane, propane). The board is equipped with a Grove connector and communicates via an analog interface. Seeed Studio 101020045
zł49.46
24h
Available quantity: 2
Available
Module with 16 RGB LEDs WS2813 Mini. The board is equipped with a Grove connector and communicates via a digital interface. Seeed Studio 104020171
zł55.63
24h
Available quantity: 3
Available
Module with MLX90615 temperature sensor with a measurement accuracy of 1°C and a resolution of 0.02°C. The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 101020077
zł173.93
24h
Available quantity: 1
Available
Module with the alcohol sensor MQ303A. The board is equipped with a Grove connector and communicates via an analog interface. Seeed Studio 101020044
zł36.60
24h
Available quantity: 3
Available
Green mounting for Grove modules, which ensure convenient installation and replacement of modules in the project. Compatible with LEGO. Set of 4. Seeed Studio 110070023
zł11.54
24h
Available quantity: 1
Available
Module with OLED display 0.96" with a resolution of 128x64 px. The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 104020208
zł31.16
24h
Available quantity: 1
Available
Yellow mounting for Grove modules, which ensure convenient installation and replacement of modules in the project. Compatible with LEGO. Set of 4. Seeed Studio 110070021
zł11.54
24h
Available quantity: 2
Available
Module with a pressure sensor with high accuracy HP206C. The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 101020068
zł121.52
24h
Available quantity: 1
Available
Starter kit for the micro:bit v2. The kit includes an expansion module with Grove connectors, Grove modules with sensors and the necessary accessories. Seeed Studio 110060762
zł405.14
24h
Available quantity: 5
Available
Module with PIR S16-L221D motion sensor. The board is equipped with a Grove connector and communicates via a digital interface. Seeed Studio 101020353
zł29.57
24h
Available quantity: 4
Available
The kit includes a control module (with ETA1617 and NE555) and an ultrasonic transducer. The water atomiser module allows for the construction of, for example, a small humidifier. The module has a connector in accordance with the Grove standard. Seeed studio 101020090