zł67.66 tax excl.
Digital signal isolator for communication via the Gravity I2C interface. It allows you to isolate the I2C digital signal and provide isolated power to the sensor module. DFRobot DFR0565
Digital signal isolator for communication via the Gravity I2C interface. It allows you to isolate the I2C digital signal and supply isolated power to the sensor module, effectively preventing mutual interference between modules. The module has a built-in 5 V isolation power supply and can directly power the sensor module (without additional power supply) with a maximum current of 150 mA. The set can be used in water quality detection systems to prevent mutual interference between sensors and actuators, e.g. pumps. A user manual is available on the Wiki page.

Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Gravity: Analog Signal Isolator is a module that allows to isolate sensors in the system and eliminate mutual interference of sensors powered by 5V. DFRobot DFR0504
Board with ATmega1280 microcontroller from the AVR family, the user has 54 I/O lines, 14 PWM channels, 16 analog inputs. DFRobot DFR0003
No product available!
Nano I / O Shield for Arduino Nano is an expansion board for Arduino Nano that provides digital, analog pins, power inputs and a connector for the Bluetooth module. DFRobot DFR0012
UART-RS485 converter module based on the TD (H) 541S485H chip. Equipped with power isolation and TVS. DFRobot DFR0845
DFRobot 315MHz RF receiver module using SC2272-L4 low power decoder chip. DFRobot TEL0112
Module with an analog sound intensity sensor. It enables measurement in the range from 30 dB to 130 dB with a measurement error of ± 1.5 dB. The module returns the output voltage in the range of 0.6 to 2.6 V. DFRobot SEN0232
No product available!
Digital orientation sensor module. DFRobot DFR0028
Module with a button, LED diode and a blue cap. DFRobot DFR0029-B
8x16 LED matrix equipped with colored LEDs and a driver. It is powered by 5 V and communicates via the I2C interface (Gravity connector). DFRobot DFR0522
Module with Hall sensor, allows for magnetic field detection, can be used to measure angle of rotation, displacement, mechanical vibrations, etc. The module has a connector in accordance with the Gravity standard. DFRobot SEN0185
No product available!
Module with 6-axis BMI160 motion sensor (accelerometer and gyroscope) with 16-bit data resolution. It is supplied with the voltage in the range from 3.2 to 6 V. I2C communication. DFRobot SEN0250
Gravity sensor adapter with 3-pin terminal connector. There are two 10 kΩ pull-up and pull down resistors on the board, set with a jumper. DFRobot DFR0055
Module with a buzzer (without generator) controlled by a digital interface. It allows you to generate simple sounds by changing the frequency of the control signal. DFRobot DFR0032
Module with 5 A 250 VAC relay. DFRobot DFR0017
Module with an analog MQ5 LPG sensor. It is powered with the voltage of 5 V and has an analog output. DFRobot SEN0130
Module with an analog MQ7 carbon monoxide sensor. It is powered with the voltage of 5 V and has an analog output. DFRobot SEN0132
Gravity: 360 Degree Hall Angle Sensor is a rotation angle sensor measuring a value in the range of 0-360 ° with an analogue output, powered by 5V. DFRobot SEN0221
Flexible 8x8 RGB LED matrix module. The set uses addressable SK6812/WS2812B diodes. DFRobot DFR0461
No product available!
Digital signal isolator for communication via the Gravity I2C interface. It allows you to isolate the I2C digital signal and provide isolated power to the sensor module. DFRobot DFR0565