Gravity: Analog Signal Isolator - analog signal isolator
ID: 566119
5902186313088
zł89.21
Tax included
zł72.53 tax excl.
Gravity: Analog Signal Isolator is a module that allows to isolate sensors in the system and eliminate mutual interference of sensors powered by 5V. DFRobot DFR0504
Description
Gravity: Analog Signal Isolator is a module that prevents electrical interference between sensors. In many cases, to ensure reliable operation of the sensors, isolation of the sensors in the device is required, because they can interfere with each other and will not perform correct measurements. The insulating module allows to separate the sensors in the device and increase the stability and reliability of operation. The module has a built-in 5V power supply, so you do not need to connect an external, additional power source for the sensor. The module has been equipped with a Gravity connector allowing easy connection of sensors to the module. The tile can be used, for example, in a multi-parameter water quality monitoring system.
In order for the module to work properly, it should be noted that:
- module power supply should be stable to achieve stable readings
- the current consumed by the sensors should not exceed 170 mA
- do not short-circuit the mass field on the sensor side and the MCU module (they are isolated)
- it is necessary to ensure heat dissipation from the module, because it can give off large amounts of heat
properties
- Response time: 4 sec
- Gravity PH2.0-3P connector
- Power consumption (without load): 75mA
- Non-insulated connector (MCU connector):
- Supply voltage: 5.0 ± 0.1 V
- Analog output: 0 ... 5.0 V
- Insulated connector (SEN connector)
- Output voltage: 5.0 ± 0.2 V
- Analog input: 0..5,0 V
- Power supply: 5 V
- Dimensions: 42 x 32mm
Included
- Gravity Module: Analog Signal Isolator
- 2 x Gravity Connection Cable (PH2.0-3P Cable)
566119
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
Single-Channel High Speed 10MBit/s Logic Gate Optocouplers, DIP8, Fairchild Semiconductor, RoHS
zł0.98
24h
Available quantity: 31
Available
Expansion board for Arduino, allows easy connection of XBee modules, has separate outputs for I2C, SPI and UART buses. The built-in 3.3V voltage stabilizer and operating mode switch make it easier to program the Arduino when the XBee module is connected to the sockets. DFRobot DFR0265
zł21.41
24h
Available quantity: 4
Available
Gravity: IO Expansion & Motor Driver Shield is an Arduino compatible expansion board that provides digital I / O ports, analog I2C, SPI and UART interfaces, as well as a DC motor driver. DFRobot DFR0502
zł65.65
24h
Available quantity: 3
Available
Other products in the same category (16)
The expansion board is designed for DFRduino M0 or Bluno M0 sets. The board has 31 GPIO pins (including 6 PWM and 6 ADC inputs), UART, I2C and SPI interfaces. The pins are color coded according to the Gravity standard. DFRobot DFR0412
zł44.59
24h
Available quantity: 1
Available
A module with an EMG sensor that detects the activity of human muscles and neurons. Generates an analog signal in the range from 0 to 3 V on the output, it does not require the use of a conductive gel. DFRobot SEN0240
zł225.72
4 weeks
No product available!
Gravity: Analog TDS Sensor / Meter is an analog water purity measurement module. It is powered by 3.3 ... 5.5V voltage and has an analogue output interface. Module compatible with Arduino. DFRobot SEN0244
zł55.51
4 weeks
No product available!
Module with an analog sound intensity sensor. It enables measurement in the range from 30 dB to 130 dB with a measurement error of ± 1.5 dB. The module returns the output voltage in the range of 0.6 to 2.6 V. DFRobot SEN0232
zł181.34
4 weeks
No product available!
Gravity: IO Expansion & Motor Driver Shield is an Arduino compatible expansion board that provides digital I / O ports, analog I2C, SPI and UART interfaces, as well as a DC motor driver. DFRobot DFR0502
zł65.65
24h
Available quantity: 3
Available
Set with a measuring module and a probe for measuring the pH of wet soil and food products. The module is powered with the voltage of 5 V and has an analog output with a voltage range from 0 to 4 V. DFRobot SEN0249
zł539.63
4 weeks
No product available!
IoT DFRobot Gravity UART OBLOQ module for working with Microsoft Azure. DFRobot TEL0118
zł55.76
24h
Available quantity: 2
Available
Water pressure sensor with 3-pin Gravity interface. It enables the measurement of liquid pressure in the range from 0 to 1.6 MPa. It is supplied with the voltage of 5 V and has a linear output voltage from 0.5 to 4.5 V. DFRobot SEN0257
zł85.85
24h
Available quantity: 3
Available
I2C BME680 Environmental Sensor is a gas, pressure, temperature and humidity sensor in one MEMS housing. The module is supplied with 3.3-5V, for communication the I2C or SPI interface is used. DFRobot SEN0248
zł112.72
24h
Available quantity: 2
Available
Gravity: Digital Peristaltic Pump is a peristaltic pump with a controller and a connector compatible with modeling servos. The set is powered by 5 ... 6 V. DFRobot DFR0523
zł111.23
24h
Available quantity: 4
Available
DFRobot Gravity analog light intensity module for Arduino and Raspberry Pi. DFRobot DFR0026
zł11.01
24h
Available quantity: 5
Available
Module with a button, LED diode and a blue cap. DFRobot DFR0029-B
zł11.30
24h
Available quantity: 3
Available
Digital orientation sensor module. DFRobot DFR0028
zł7.44
24h
Available quantity: 1
Available
Module with 5 A 250 VAC relay. DFRobot DFR0017
zł12.63
24h
Available quantity: 3
Available
Fan module with DC motor, propeller and connection cable. DFRobot DFR0332
zł29.22
24h
Available quantity: 3
Available
LM35 analog temperature sensor module for Arduino. DFRobot DFR0023
zł15.51
24h
Available quantity: 1
Available
Gravity: Analog Signal Isolator is a module that allows to isolate sensors in the system and eliminate mutual interference of sensors powered by 5V. DFRobot DFR0504