zł6.74 tax excl.
Gravity module with a colored RGB WS2812 LED. Thanks to the controller built into the diode, you can connect the modules in series and control all with one microcontroller port. DFRobot DFR0605
Gravity module with RGB LED can be controlled from various platforms such as Arduino , micro: bit , Raspberry pi , LattePanda, etc. The board contains multi-color digital diode WS2812, which can be controlled by one digital port, which is compared to ordinary RGB diodes. which must be controlled by three PWM ports is a big advantage, moreover, WS2812 diodes can be connected in series, so you can control over 100 diodes with one microcontroller port.
The modules can be supplied with voltage from 3.3 V to 5.5 V, diodes take up to 48 mA, while in idle mode they download 0.7 mA. Tiles can be combined with each other using Gravity 3P connectors, this type of cable is included in the set so you can connect multiple modules without the need to trim and solder the wires. The LEDs change color smoothly, allowing you to create various effects such as flashing, breathing or rainbow. Arranging modules in the right way allows even displaying text or animation.
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
WS2812S is a three-color, closed in a housing with a controller, RGB diode in an SMD5050 housing with PLCC-6 terminals. The diodes can be connected in series, thanks to which you can control whole chains of such diodes with three wires.
KAmodWS2812-1 is a module with WS2812 multicolor LED. Thanks to the embedded controller, LED can be series connected to makes an amazing light effects. KAmodWS2812-1
The ring has sixteen RGB WS2812 diodes, controlled by means of serial signals. The module can be supplied with voltage from 4-7V, only one signal line is required to control it. NeoPixel Ring 16 x WS2812B
KAmodWS2812-1 is a module with WS2812 multicolor LED. Thanks to the embedded controller, LED can be series connected to makes an amazing light effects. KAmodWS2812-1
A small module for learning how to solder. It allows you to build a small device with two LEDs that turn on when the light intensity changes
HK Blue 16 LED Circular Light Board with Lead (28512)
A module for building a rear bicycle light using 1000 mCd red LEDs. Power supplied by AA batteries, which are not included in the kit. Kitronik 2106
Module with yellow LED, digitally controlled. Perfect for people starting to play with Arduino. Equipped with a Gravity interface. DFRobot DFR0031-Y
The Satellite Module 001 is an RGB LED module from macetech, containing ten 100 mA 5-chip wide-angle (140 degree) red, green, and blue LEDs. The module runs at 10 V, for a maximum power of 3 W, and it is connected in a common-anode configuration. Pololu 1243
A set of 10 mini modules with addressable RGBW Neopixel LEDs. The diodes are controlled using a popular single-wire interface, and their design allows the modules to be connected in series. Adafruit 4776
Module with red LED, digitally controlled. Perfect for people starting to play with Arduino. Equipped with a Gravity interface. DFRobot DFR0021-R
Module with white LED diode and potentiometer. The board is equipped with a Grove connector and communicates via a digital interface. Seeed Studio 104030009
Module with flashing multi-color LED. The board is equipped with a Grove connector and communicates via a digital interface. Seeed Studio 104030014
No product available!
Module with white LED, digitally controlled. Perfect for people starting to play with Arduino. Equipped with a Gravity interface. DFRobot DFR0021-W
Module with green LED, digitally controlled. Perfect for people starting to play with Arduino. Equipped with a Gravity interface. DFRobot DFR0021-G
HK Yellow 16 LED Circular Light Board with Lead (28511)
Digitally controlled module with LED. Perfect for people starting their fun with Arduino. Equipped with an XH2.54 connector
Kitronik 2723 is a green LED designed for use in e-textiles, allowing for easy integration of lighting effects into textile projects. With a built-in resistor and clearly marked polarity (+ and -), the LED is simple to use and safe to incorporate with conductive materials.
Module with two white diodes. Dedicated to Voron 3D printers as hotend and printing nozzle lighting
Gravity module with a colored RGB WS2812 LED. Thanks to the controller built into the diode, you can connect the modules in series and control all with one microcontroller port. DFRobot DFR0605