Gravity: I2C 3.7V Li Battery Fuel Gauge - charge flow control
ID: 571797
5906623405817
zł46.40
Tax included
zł37.72 tax excl.
Gravity: I2C 3.7V Li Battery Fuel Gauge is a module for monitoring the parameters of the Li-ion battery allowing for precise measurement of the flow of charge to / from a 1-source source with an input voltage of 2.5-4.2V. DFRobot DFR0563
Description
Gravity: I2C 3.7V Li Battery Fuel Gauge is a Li-ion battery parameter control module. The module can control the status of a 1-purpose power source. Thanks to the precise measurement of the flow of electrical charge to and from the battery and the advanced algorithm, it is possible to determine the exact level of the battery charge. The system has a built-in system for eliminating offset errors and the ability to set a low-battery notification. The module has Gravity connectors and is easy to use with popular development kits. Communication with the module takes place via the I2C interface. It can be used in projects that require battery status control, eg in solar systems.
properties
- Battery input voltage (BAT IN): 2.5-4.2 V
- Battery type (BAT IN): 3.7 V Li-polymer / Li-ion
- Power consumption: 50 uA
- Interface: I2C
- Gravity connector
- Supply voltage (VCC): 3.3-6.0 V
- Dimensions: 22 x 30 mm
Included
- Gravity Module: I2C 3.7V Li Battery Fuel Gauge
- Connector XH2.54-2P Header
- Connecting cable Gravity-4P I2C / UART Sensor Wire
571797
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
Available
Expansion board for Arduino, allows easy connection of XBee modules, has separate outputs for I2C, SPI and UART buses. The built-in 3.3V voltage stabilizer and operating mode switch make it easier to program the Arduino when the XBee module is connected to the sockets. DFRobot DFR0265
zł21.65
24h
Available quantity: 1
Available
Gravity: IO Expansion & Motor Driver Shield is an Arduino compatible expansion board that provides digital I / O ports, analog I2C, SPI and UART interfaces, as well as a DC motor driver. DFRobot DFR0502
zł65.65
24h
Available quantity: 3
Available
Other products in the same category (16)
A set of 5 modules with a button and LED backlight. The boards are equipped with a Gravity connector and communicate via a digital interface. DFRobot DFR0785
zł100.92
24h
Available quantity: 1
Available
Gravity: Joystick Module V2 is a joystick module with two analog outputs (X and Y axis) and a digital output (Z axis) supplied with 3.3 ... 5V voltage. DFRobot DFR0061
zł23.70
24h
Available quantity: 2
Available
Flexible 16x16 RGB LED matrix module. The set uses addressable SK6812/WS2812B diodes. DFRobot DFR0463
zł414.47
4 weeks
No product available!
Module with an analog sensor of carbon monoxide and combustible gases (methane, propane) MQ9. It is powered with the voltage of 5 V and has an analog output. DFRobot SEN0134
zł41.22
24h
Available quantity: 1
Available
Module with a buzzer (without generator) controlled by a digital interface. It allows you to generate simple sounds by changing the frequency of the control signal. DFRobot DFR0032
zł13.90
24h
Available quantity: 1
Available
Gravity: The high temperature sensor is a sensor based on the PT100 probe and adapted to very high temperatures (30-350 ° C). The module is powered by 3.3 ... 5.5V voltage. DFRobot SEN0198
zł72.46
24h
Available quantity: 2
Available
Gravity: I2C ADS1115 The 16-Bit ADC Module is an analogue-to-digital converter module for Arduino and Raspberry Pi. This module uses 16-bit ADC ADS1115 and is powered by 3.3 ... 5V. DFRobot DFR0553
zł72.56
24h
Available quantity: 5
Available
Gravity: Analog Sound Sensor is a sound sensor with Gravity analogue output. The module can be supplied with 3.3 ... 5V voltage. DFRobot DFR0034
zł21.41
24h
Available quantity: 3
Available
Module with an analog MQ2 gas sensor. It enables the detection of LPG, butane, propane, methane, alcohol, hydrogen and smoke. It is powered with the voltage of 5 V and has an analog output. DFRobot SEN0127
zł33.27
24h
Available quantity: 1
Available
The arduino turbidity sensor detects water quality by measuring level of turbidity. It is able to detect suspended particles in water by measuring the light transmittance and scattering rate which changes with the amount of total suspended solids (TSS) in water. SEN0189
zł70.60
24h
Available quantity: 3
Available
4-digit, 8-segment LED display module with 8-level brightness adjustment. Communication via the I2C interface. DFRobot DFR0645-G
zł22.95
24h
Available quantity: 1
Available
Module with red LED, digitally controlled. Perfect for people starting to play with Arduino. Equipped with a Gravity interface. DFRobot DFR0031-R
zł11.53
24h
Available quantity: 1
Available
2x1.2A DC Motor Driver is a dual controller of DC motors with a Gravity connector, supplied with 2.5 ... 12V voltage with a maximum current consumption of 1.2A (3.2A peak) per channel. DFRobot DRI0044-A
zł40.02
24h
Available quantity: 1
Available
Sensor that detects the concentration of chlorine. Equipped with a factory calibrated probe. It communicates via the I2C interface, UART or analog output. DFRobot SEN0468
zł722.94
4 weeks
No product available!
A 24-channel input/output port expander module controlled by an I2C interface. It was based on the CH423 chip and equipped with a Gravity connector. DFRobot DFR0979
zł22.83
24h
Available quantity: 2
Available
Module with liquid level sensor. The set includes a current-voltage converter that generates an analog signal. DFRobot KIT0139
zł231.66
24h
Available quantity: 2
Available
Gravity: I2C 3.7V Li Battery Fuel Gauge is a module for monitoring the parameters of the Li-ion battery allowing for precise measurement of the flow of charge to / from a 1-source source with an input voltage of 2.5-4.2V. DFRobot DFR0563