 
        
           
        
           
         
           
           
           
           
           
           
          DC Micro motor module with metal gear with a gear ratio of 30:1. The motor is connected to the board containing the driver, so the motor can be controlled via the Gravity connector directly by the microcontroller (no additional H-bridge required). The set is controlled by the PWM signal, analogically to the servo. The module is characterized by low current consumption (less than 1 mA in the absence of a control signal). The user manual with a sample program is available on the product Wiki page.
Data sheet
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Board with ATmega2560 microcontroller (256 kB Flash, 8 kB RAM, 4 kB EEPROM) clocked at 16 MHz. USB-UART converter based on the ATmega16u2 chip. The user has at his disposal, among others: 54 I/O lines, 14 PWM channels, 16 analog inputs.
Board with Atmel ATmega328 microcontroller from the AVR family, there are 14 I / O lines, 6 PWM channels and 6 analog inputs. The additional ATmega16U4 microcontroller realizes communication via the USB interface
DC Micro motor module with metal gear with a gear ratio of 50:1. The motor is connected to the board containing the driver. DFRobot DFR0429
DC Micro motor module with metal gear with a gear ratio of 75:1. The motor is connected to the board containing the driver. DFRobot DFR0399
Module with the ATMega4809 microcontroller from the AVR family (48 KB Flash, 6 KB SRAM, 256 B EEPROM). The module has two 15-pin connectors equipped with GPIO, SPI, I2C, PWM, USART, DAC and ADC. Arduino ABX00028
Board with nRF52840 microcontroller with Cortex M4F core (64 MHz, 1 MB Flash, 256 kB RAM). Equipped with BT 5.0 and IMU LSM9DS1 module. Module with headers. Arduino ABX00034
Small metal gear motor, 1000 RPM speed, 6V operating voltage. GA12-N20-0018
 No product available!
A small, low-power motor with a 10:1 metal gear, operating voltage of 6 V, power consumption from 0.02 A to 0.36 A, speed of 1300 RPM, maximum torque of 0.1 kg*cm and double-sided shaft. Pololu 2201
 No product available!
This gearmotor is a miniature high-power, 6 V brushed DC motor with long-life carbon brushes and a 9.96:1 metal gearbox. It has a cross section of 10 × 12 mm, and the D-shaped gearbox output shaft is 9 mm long and 3 mm in diameter. This version also has a 4.5 × 1 mm extended motor shaft.
A small medium-power motor with a 30:1 metal gear, 6 V operating voltage, 0.04 A to 0.67 A power consumption, 720 RPM, a maximum torque of 0.33 kg*cm and a double-sided shaft. Pololu 2378
 No product available!
 No product available!
Miniature, 12 V brush DC motor with metal gear and 15.25:1 gear ratio. It has a cross section of 10 × 12 mm, and the D-shaped output shaft with a length of 9 mm and a diameter of 3 mm. Pololu 4788
 No product available!
298:1 Micro Metal Gearmotor
Pololu high power miniature motor with carbon brushes. 380:1 gear motor, shaft speed 85 rpm, torque 5kg*cm. The motor has an extended shaft, which makes it easy to attach the encoder. Pololu 4799
A small, high-power motor with a 380: 1 metal gear, 6 V operating voltage, 0.1 A to 1.5 A power consumption, 85 RPM, a maximum torque of 5 kg * cm and carbon brushes with increased durability. Pololu 4796
 No product available!
A small, high-power motor with a 380: 1 metal gear, 12 V operating voltage, 0.06 A to 0.75 A power consumption, 85 RPM, a maximum torque of 5 kg * cm and carbon brushes with increased durability. Pololu 4798
 No product available!
 No product available!
Miniature high-power, 6 V brushed DC motor with long-life carbon brushes and a 75.81:1 metal gearbox. It has a cross section of 10 × 12 mm, and the D-shaped gearbox output shaft is 9 mm long and 3 mm in diameter. This version also has a 4.5 × 1 mm extended motor shaft. Pololu 3074
 No product available!
Small metal gear motor, 30 RPM speed, 6V operating voltage. GA12-N20-0011
150:1 Micro Metal Gearmotor HP
Miniature medium-power, 6 V brushed DC motor with a 51.45:1 metal gearbox. It has a cross section of 10 × 12 mm, and the D-shaped gearbox output shaft is 9 mm long and 3 mm in diameter. Pololu 2365
 No product available!
Small metal gear motor, rotation speed 136 RPM, operating voltage 6 V. GA1024-N20F-0037
 
                    DC Micro motor module with metal gear with a gear ratio of 30:1. The motor is connected to the board containing the driver. DFRobot DFR0399