Pololu 3061 - 10:1 Micro Metal Gearmotor HPCB 6V
ID: 562767
zł96.46
Tax included
zł78.42 tax excl.
This gearmotor is a miniature high-power, 6 V brushed DC motor with long-life carbon brushes and a 9.96:1 metal gearbox. It has a cross section of 10 × 12 mm, and the D-shaped gearbox output shaft is 9 mm long and 3 mm in diameter.
Free shipping
free shipping in Poland for all orders over 500 PLN
Same day shipping
If your payment will be credited to our account by 11:00
14 days for return
Each consumer can return the purchased goods within 14 days
Overview:
These tiny brushed DC gearmotors are available in a wide range of gear ratios—from 5:1 up to 1000:1—and with five different motors: high-power 6 V and 12 V motors with long-life carbon brushes (HPCB), and high-power (HP), medium power (MP), and low power (LP) 6 V motors with shorter-life precious metal brushes. The 6 V and 12 V HPCB motors offer the same performance at their respective nominal voltages, just with the 12 V motor drawing half the current of the 6 V motor. The 6 V HPCB and 6 V HP motors are identical except for their brushes, which only affect the lifetime of the motor.
The HPCB versions (shown on the left in the picture below) can be differentiated from versions with precious metal brushes (shown on the right) by their copper-colored terminals. Note that the HPCB terminals are 0.5 mm wider than those on the other micro metal gearmotor versions (2 mm vs. 1.5 mm), and they are about 1 mm closer together (6 mm vs. 7 mm).
Versions of these gearmotors are also available with an additional 1 mm-diameter output shaft that protrudes from the rear of the motor. This 4.5 mm-long rear shaft rotates at the same speed as the input to the gearbox and offers a way to add an encoder, such as our magnetic encoder for micro metal gearmotors (see the picture on the right), to provide motor speed or position feedback.
With the exception of the 1000:1 gear ratio versions, all of the micro metal gearmotors have the same physical dimensions, so one version can be easily swapped for another if your design requirements change. Please see the micro metal gearmotor comparison table for detailed specifications of all our micro metal gearmotors. This dynamically-sortable table can help you find the gearmotor that offers the best blend of speed, torque, and current-draw for your particular application. A more basic comparison table is available below.
| Rated Voltage | Motor Type | Stall Current @ Rated Voltage | No-Load Speed @ Rated Voltage | Approximate Stall Torque @ Rated Voltage |  Single-Shaft (Gearbox Only) |  Dual-Shaft (Gearbox & Motor) |
|---|---|---|---|---|---|---|
| 12 V | high-power, carbon brushes (HPCB) |
800 mA | 6000 RPM | 2 oz-in | 5:1 HPCB 12V | 5:1 HPCB 12V dual-shaft |
| 3000 RPM | 4 oz-in | 10:1 HPCB 12V | 10:1 HPCB 12V dual-shaft | |||
| 1000 RPM | 9 oz-in | 30:1 HPCB 12V | 30:1 HPCB 12V dual-shaft | |||
| 625 RPM | 15 oz-in | 50:1 HPCB 12V | 50:1 HPCB 12V dual-shaft | |||
| 400 RPM | 22 oz-in | 75:1 HPCB 12V | 75:1 HPCB 12V dual-shaft | |||
| 320 RPM | 30 oz-in | 100:1 HPCB 12V | 100:1 HPCB 12V dual-shaft | |||
| 200 RPM | 40 oz-in | 150:1 HPCB 12V | 150:1 HPCB 12V dual-shaft | |||
| 140 RPM | 50 oz-in | 210:1 HPCB 12V | 210:1 HPCB 12V dual-shaft | |||
| 120 RPM | 60 oz-in | 250:1 HPCB 12V | 250:1 HPCB 12V dual-shaft | |||
| 100 RPM | 70 oz-in | 298:1 HPCB 12V | 298:1 HPCB 12V dual-shaft | |||
| 32 RPM | 125 oz-in | 1000:1 HPCB 12V | 1000:1 HPCB 12V dual-shaft | |||
| 6 V | high-power, carbon brushes (HPCB) |
1600 mA | 6000 RPM | 2 oz-in | 5:1 HPCB 6V | 5:1 HPCB 6V dual-shaft |
| 3000 RPM | 4 oz-in | 10:1 HPCB 6V | 10:1 HPCB 6V dual-shaft | |||
| 1000 RPM | 9 oz-in | 30:1 HPCB 6V | 30:1 HPCB 6V dual-shaft | |||
| 625 RPM | 15 oz-in | 50:1 HPCB 6V | 50:1 HPCB 6V dual-shaft | |||
| 400 RPM | 22 oz-in | 75:1 HPCB 6V | 75:1 HPCB 6V dual-shaft | |||
| 320 RPM | 30 oz-in | 100:1 HPCB 6V | 100:1 HPCB 6V dual-shaft | |||
| 200 RPM | 40 oz-in | 150:1 HPCB 6V | 150:1 HPCB 6V dual-shaft | |||
| 140 RPM | 50 oz-in | 210:1 HPCB 6V | 210:1 HPCB 6V dual-shaft | |||
| 120 RPM | 60 oz-in | 250:1 HPCB 6V | 250:1 HPCB 6V dual-shaft | |||
| 100 RPM | 70 oz-in | 298:1 HPCB 6V | 298:1 HPCB 6V dual-shaft | |||
| 32 RPM | 125 oz-in | 1000:1 HPCB 6V | 1000:1 HPCB 6V dual-shaft | |||
| 6 V | high-power (HP) (same specs as 6V HPCB above) |
1600 mA | 6000 RPM | 2 oz-in | 5:1 HP 6V | 5:1 HP 6V dual-shaft |
| 3000 RPM | 4 oz-in | 10:1 HP 6V | 10:1 HP 6V dual-shaft | |||
| 1000 RPM | 9 oz-in | 30:1 HP 6V | 30:1 HP 6V dual-shaft | |||
| 625 RPM | 15 oz-in | 50:1 HP 6V | 50:1 HP 6V dual-shaft | |||
| 400 RPM | 22 oz-in | 75:1 HP 6V | 75:1 HP 6V dual-shaft | |||
| 320 RPM | 30 oz-in | 100:1 HP 6V | 100:1 HP 6V dual-shaft | |||
| 200 RPM | 40 oz-in | 150:1 HP 6V | 150:1 HP 6V dual-shaft | |||
| 140 RPM | 50 oz-in | 210:1 HP 6V | 210:1 HP 6V dual-shaft | |||
| 120 RPM | 60 oz-in | 250:1 HP 6V | 250:1 HP 6V dual-shaft | |||
| 100 RPM | 70 oz-in | 298:1 HP 6V | 298:1 HP 6V dual-shaft | |||
| 32 RPM | 125 oz-in | 1000:1 HP 6V | 1000:1 HP 6V dual-shaft | |||
| 6 V | medium-power (MP) |
700 mA | 4400 RPM | 1.5 oz-in | 5:1 MP 6V dual-shaft | |
| 2200 RPM | 3 oz-in | 10:1 MP 6V | 10:1 MP 6V dual-shaft | |||
| 730 RPM | 8 oz-in | 30:1 MP 6V | 30:1 MP 6V dual-shaft | |||
| 420 RPM | 12 oz-in | 50:1 MP 6V | 50:1 MP 6V dual-shaft | |||
| 290 RPM | 17 oz-in | 75:1 MP 6V | 75:1 MP 6V dual-shaft | |||
| 220 RPM | 21 oz-in | 100:1 MP 6V | 100:1 MP 6V dual-shaft | |||
| 150 RPM | 28 oz-in | 150:1 MP 6V | 150:1 MP 6V dual-shaft | |||
| 100 RPM | 36 oz-in | 210:1 MP 6V dual-shaft | ||||
| 90 RPM | 41 oz-in | 250:1 MP 6V dual-shaft | ||||
| 75 RPM | 46 oz-in | 298:1 MP 6V | 298:1 MP 6V dual-shaft | |||
| 22 RPM | 80 oz-in | 1000:1 MP 6V | 1000:1 MP 6V dual-shaft | |||
| 6 V | low-power (LP) |
360 mA | 2500 RPM | 1 oz-in | 5:1 LP 6V | 5:1 LP 6V dual-shaft |
| 1300 RPM | 2 oz-in | 10:1 LP 6V | 10:1 LP 6V dual-shaft | |||
| 440 RPM | 4 oz-in | 30:1 LP 6V | 30:1 LP 6V dual-shaft | |||
| 250 RPM | 7 oz-in | 50:1 LP 6V | 50:1 LP 6V dual-shaft | |||
| 170 RPM | 9 oz-in | 75:1 LP 6V | 75:1 LP 6V dual-shaft | |||
| 120 RPM | 12 oz-in | 100:1 LP 6V | 100:1 LP 6V dual-shaft | |||
| 85 RPM | 17 oz-in | 150:1 LP 6V | 150:1 LP 6V dual-shaft | |||
| 60 RPM | 27 oz-in | 210:1 LP 6V | 210:1 LP 6V dual-shaft | |||
| 50 RPM | 32 oz-in | 250:1 LP 6V | 250:1 LP 6V dual-shaft | |||
| 45 RPM | 40 oz-in | 298:1 LP 6V | 298:1 LP 6V dual-shaft | |||
| 14 RPM | 70 oz-in | 1000:1 LP 6V | 1000:1 LP 6V dual-shaft | |||
Note: Stalling or overloading gearmotors can greatly decrease their lifetimes and even result in immediate damage. The recommended upper limit for instantaneous torque is 35 oz-in (2.5 kg-cm) for the 1000:1 gearboxes and 25 oz-in (2 kg*cm) for all the other gear ratios; we strongly advise keeping applied loads well under this limit. Stalls can also result in rapid (potentially on the order of seconds) thermal damage to the motor windings and brushes, especially for the versions that use high-power (HP and HPCB) motors; a general recommendation for brushed DC motor operation is 25% or less of the stall current.
In general, these kinds of motors can run at voltages above and below their nominal voltages; lower voltages might not be practical, and higher voltages could start negatively affecting the life of the motor.
Gearmotor Dimensions
In terms of size, these gearmotors are very similar to Sanyo’s popular 12 mm NA4S DC gearmotors, and gearmotors with this form factor are occasionally referred to as N20 motors. The versions with carbon brushes (HPCB) have slightly different terminal and end-cap dimensions than the versions with precious metal brushes, but all of the other dimensions are identical.
Dimensions:
| Size: | 10 × 12 × 26 mm1 |
|---|---|
| Weight: | 9.5 g |
| Shaft diameter: | 3 mm2 |
General specifications:
| Gear ratio: | 9.96:1 |
|---|---|
| Free-run speed @ 6V: | 3000 rpm |
| Free-run current @ 6V: | 120 mA |
| Stall current @ 6V: | 1600 mA |
| Stall torque @ 6V: | 4 oz·in |
| Extended motor shaft?: | N |
| Long-life carbon brushes?: | Y |
| Motor type: | 1.6A stall @ 6V (HPCB 6V - carbon brush) |
Notes:
- 1 Output shaft adds 9 mm to the 26 mm length.
- 2 D shaft.
562767
Data sheet
- DC motor power
- HPCB
- Gear material
- Metal
- Gear ratio
- 10:1
- Rotation speed
- 3 300 RPM
- Shaft diameter
- 3 mm
- Shaft shape
- D
- Obustronny wał silnika
- Nie
- Power supply voltage
- 6V
Other products in the same category (16)
Pololu high power miniature motor with carbon brushes. 380:1 gear motor, shaft speed 85 rpm, torque 5kg*cm. The motor has an extended shaft, which makes it easy to attach the encoder. Pololu 4799
zł113.86
24h
Available quantity: 4
Available
Miniature high-power motor from the Pololu MP series. Gear motor 250: 1, shaft speed is 90 rpm, torque is 3 kg * cm (0.3 Nm). The motor has an extended shaft which makes it easy to attach the encoder. Pololu 2384
zł101.56
6 weeks
No product available!
Small metal gear motor, 100 RPM speed, 12V operating voltage. GA12-N20-0023
zł22.72
24h
Available quantity: 2
Available
A small, high-power motor with a 250: 1 metal gear, 6 V operating voltage, 0.1 A to 1.5 A power consumption, 130 RPM, a maximum torque of 3.2 kg * cm and carbon brushes with increased durability. Pololu 3068
zł108.97
6 weeks
No product available!
Small metal gear motor, 60 RPM speed, 6V operating voltage. GA12-N20-0013
zł22.72
24h
Available quantity: 6
Available
This gearmotor is a miniature high-power, 6 V brushed DC motor with long-life carbon brushes and a 4.995:1 metal gearbox. It has a cross section of 10 × 12 mm, and the D-shaped gearbox output shaft is 9 mm long and 3 mm in diameter. This version also has a 4.5 × 1 mm extended motor shaft.
zł99.51
24h
Available quantity: 1
Available
This gearmotor is a miniature high-power, 12 V brushed DC motor with long-life carbon brushes and a 297.92:1 metal gearbox. It has a cross section of 10 × 12 mm, and the D-shaped gearbox output shaft is 9 mm long and 3 mm in diameter. This version also has a 4.5 × 1 mm extended motor shaft.
zł114.08
24h
Available quantity: 1
Available
Small metal gear motor, 1000 RPM speed, 6V operating voltage. GA12-N20-0018
zł17.37
24h
Available quantity: 24
Available
Small metal gear motor, 30 RPM speed, 12V operating voltage. GA12-N20-0020
zł22.72
24h
Available quantity: 1
Available
A small motor with a metal gear ending with a shaft with M3 thread, rotation speed 100 RPM, operating voltage 6 V. GA1036-N20M-0055
zł29.82
24h
Available quantity: 4
Available
Small metal gear motor, 30 RPM speed, 6V operating voltage. GA12-N20-0011
zł22.72
24h
Available quantity: 3
Available
This gearmotor is a miniature high-power, 6 V brushed DC motor with long-life carbon brushes and a 150.58:1 metal gearbox. It has a cross section of 10 × 12 mm, and the D-shaped gearbox output shaft is 9 mm long and 3 mm in diameter.
zł96.56
24h
Available quantity: 1
Available
A small, high power motor with 380: 1 metal gear, 6 V operating voltage, 0.07 A to 1.6 A power consumption, 84 RPM and a maximum torque of 5.5 kg * cm. Pololu 4794
zł96.73
6 weeks
No product available!
Small metal gear motor, 300 RPM speed, 6V operating voltage. GA12-N20-0016
zł22.72
24h
Available quantity: 1
Available
A small motor with a metal gear ending with a shaft with M3 thread, rotation speed 50 RPM, operating voltage 6 V. GA1036-N20M-0053
zł29.82
24h
Available quantity: 8
Available
No product available!
This gearmotor is a miniature high-power, 6 V brushed DC motor with long-life carbon brushes and a 9.96:1 metal gearbox. It has a cross section of 10 × 12 mm, and the D-shaped gearbox output shaft is 9 mm long and 3 mm in diameter.