Products
Categories
- Main categories
-
- 3D PRINTING
- ACADEMIC OFFER
- ARDUINO
- AUTOMATION
- BOOKS
- DIY KITS
- AVT kits
- Audio
- Car
- Chargers
- Clocks, timers and schedule switches
- Communication
- Converters
- Development kits and modules
- Displays
- Electronic games
- Generators
- Hobbies and fun
- House
- Interfaces
- Light effects
- meters
- PC
- Power Supplies
- Pre-programmed circuits
- Printed circuit boards (PCB)
- Programmers
- Regulators, controllers
- Remote control
- Starter sets Ośla Łączka
- Starting sets for beginners
- Workshop tools
- Audio
- Other sets
- TOP-Q kits
- Totem
- UGears
- Velleman
- AVT kits
- EBOOKS
- ELECTRONICS
- Cables
- Cameras and accessories
- Communication
- Conductive materials
- Connectors
- ARK connectors (Terminal Block)
- Coaxial connectors (RF)
- Connectors
- Crocodile clip
- D-Sub drawer connectors
- DC power connectors
- FFC/FPC ZIF connectors
- Goldpin connectors
- IDC connectors
- JACK connectors
- JST connectors
- Jumpers
- Memory cards slots
- Other connectors
- Pogo pin
- RJ45 sockets
- Slip ring connector
- Supports
- Szybkozłącza
- USB connectors
- Cooling
- Displays
- Electronic modules
- A/D and D/A converters
- Audio
- Barcode readers
- CAN converters
- Converters USB - UART / RS232
- Data logger
- DDS/PLL generators
- Digital potentiometers
- Encoders
- Expanders of the I/O
- Fingerprint readers
- HMI modules
- Image and video
- JTAG accessories
- Keyboards, buttons
- LED drivers
- Memory card readers
- Memory modules
- Modules with power outputs
- Motor controllers
- Power modules
- RS485 converters
- RTC modules
- Servo Controllers
- TSOP infrared receivers
- USB Converters - I2C / 1-Wire / SPI
- Voltage converters
- Gadgets
- GPS
- Intelligent clothes
- LED - diodes, displays, stripes
- Luminous wires and accessories
- Memory cards and other data storages
- Passive elements
- PC accessories
- Printers
- Prototype boards
- Semiconductors
- A/C converters (ADC)
- Analog systems
- Audio systems
- Bridge rectifiers
- Button
- D/A Converters (DAC)
- DDS synthesizers
- Digital circuits
- Diodes
- Drivers of motors
- DSP microprocessors
- Energy counters
- Energy harvesting
- ESD security
- IGBT drivers and bridges
- Interface systems
- LED drivers
- Logic converters
- Memory
- Microcontrollers
- Optotriacs and optocouplers
- Other
- PLL generators
- Power systems
- Programmable systems
- Resetting systems
- RF systems
- RTC systems
- Sensors
- SoC systems
- Timery
- Touch sensors
- Transistors
- Sensors
- Accelerometers
- Air humidity sensors
- Air quality sensors
- Current sensors
- Distance sensors
- Flow sensors
- Gas sensors
- Gyroscopes
- Hall sensors
- Humidity sensors
- Infrared sensors
- Light and color sensors
- Liquid level sensors
- Magnetic sensors (compasses)
- Medical sensors
- Motion sensors
- PH sensors
- Position sensors
- Pressure sensors
- Pressure sensors
- Reflection sensors
- Sensors 6DOF/9DOF/10DOF
- Sensors of liquid quality
- Temperature sensors
- Vibration sensors
- Sound transducers
- Switches and buttons
- Cables
- INTERNET OF THINGS (IoT)
- MECHANICS
- POWER
- R/C MODELLING
- RASPBERRY PI
- Accessories for Raspberry Pi
- Audio video cables for Raspberry Pi
- Case Raspberry Pi
- Cooling for Raspberry Pi
- Displays for Raspberry Pi
- Extension modules for Raspberry Pi
- Memory cards for Raspberry Pi
- Power for Raspberry Pi
- Raspberry Pi 3 model A+
- Raspberry Pi 3 model B
- Raspberry Pi 3 model B+
- Raspberry Pi 4 model B
- Raspberry Pi 400
- Raspberry Pi 5
- Raspberry Pi cameras
- Raspberry Pi Compute Module
- Raspberry Pi model A/ B+/2
- Raspberry Pi Pico
- Raspberry Pi prototyping
- Raspberry Pi Zero
- Raspberry Pi Zero 2 W
- RETIRED PRODUCTS
- ROBOTICS
- SALE
- SOFTWARE
- STARTER KITS, PROGRAMMERS, MODULES
- Alchitry FPGA
- Altera FPGA
- Analog electronics
- Atmel SAM
- Atmel Xplain
- AVR
- Banana Pi
- BeagleBone
- chipKIT
- Coral
- CPLD Xilinx
- Cubieboard
- DFRobot FireBeetle
- Feather
- Freedom (Kinetis)
- FriendlyELEC
- HummingBoard
- Intelligent clothes
- Kit with a book
- LattePanda
- LPC (NXP)
- M5Stack
- Micro:bit
- Nvidia Jetson
- Odroid
- ODYSSEY
- Orange Pi
- Other development kits
- Peripheral modules
- PIC
- Raisonance
- Raspberry Pi RP2040
- RFID
- RISC-V
- SBC Embest
- SBC MYIR
- SBC others
- SBC UDOO
- Segger programmers
- SoMLabs
- Sparkfun MicroMod
- STM32
- STM32 Discovery
- STM32 MP1
- STM32 Nucleo boards
- STM8
- Teensy
- Universal programmers
- WRTNode
- Xilinx FPGAs
- WORKSHOP
- Adhesives and gluers
- Anti-static mats (ESD)
- Chemistry
- CNC milling machines
- Crimping tools
- Dispensing needles
- Drills
- Files
- Generators
- Handles, magnifiers
- Heat-shrink tubing
- Insulation strippers
- Keys
- Knives and scissors
- Laboratory power supplies
- Laminates
- Measuring devices
- Mikroskopy
- Mini drills and grindrers
- Organizers
- Oscilloscopes and accessories
- Pliers and pincers
- Riveting tools and rivets
- Screwdrivers
- SMD Accessories
- Soldering
- Tapes (aluminum, kapton, copper, insulating)
- Tweezers
- Ultrasonic cleaners
- Vices
- 3D PRINTING
New products
New products
zł82.65 tax excl.
A small, low-power motor with a 150:1 metal gear, operating voltage of 6 V, power consumption from 0.02 A to 0.36 A, speed of 90 RPM, maximum torque of 1.1 kg*cm and double-sided shaft. Pololu 2205
Free shipping
free shipping in Poland for all orders over 500 PLN
Same day shipping
If your payment will be credited to our account by 11:00
14 days for return
Each consumer can return the purchased goods within 14 days
This gearmotor is a miniature low-power, 6 V brushed DC motor with a 150.58:1 metal gearbox. It has a cross section of 10 × 12 mm, and the D-shaped gearbox output shaft is 9 mm long and 3 mm in diameter. This version also has a 4.5 × 1 mm extended motor shaft.
voltage | no-load performance | stall extrapolation |
---|---|---|
6 V | 90 RPM, 20 mA | 1.1 kg⋅cm (15 oz⋅in), 0.36 A |
Overview
These tiny brushed DC gearmotors are available in a wide range of gear ratios—from 5:1 up to 1000:1—and with five different motors: high-power 6 V and 12 V motors with long-life carbon brushes (HPCB), and high-power (HP), medium power (MP), and low power (LP) 6 V motors with shorter-life precious metal brushes. The 6 V and 12 V HPCB motors offer the same performance at their respective nominal voltages, just with the 12 V motor drawing half the current of the 6 V motor. The 6 V HPCB and 6 V HP motors are identical except for their brushes, which only affect the lifetime of the motor.The HPCB versions (shown on the left in the picture below) can be differentiated from versions with precious metal brushes (shown on the right) by their copper-colored terminals. Note that the HPCB terminals are 0.5 mm wider than those on the other micro metal gearmotor versions (2 mm vs. 1.5 mm), and they are about 1 mm closer together (6 mm vs. 7 mm).
Gearmotor Dimensions
Dimensions of the Pololu micro metal gearmotors with precious metal brushes: low-power (LP), medium-power (MP), and high-power (HP). Units are mm over [inches]. |
---|
Dimensions of the Pololu micro metal gearmotors with carbon brushes (HPCB). Units are mm over [inches]. |
In terms of size, these gearmotors are very similar to Sanyo’s popular 12 mm NA4S DC gearmotors, and gearmotors with this form factor are occasionally referred to as N20 motors. The versions with carbon brushes (HPCB) have slightly different terminal and end-cap dimensions than the versions with precious metal brushes, but all of the other dimensions are identical.
Note: The gearbox on the 1000:1 and 1000:1 HP micro metal gearmotors is 12.5 mm long. All of the other micro metal gearmotors have 9mm-long gearboxes, as shown in the above dimension diagram.
Motor Accessories
- Wheels and Hubs: The micro metal gearmotor’s output shaft matches our assortment of Pololu wheels and the Solarbotics RW2 rubber wheel. You can also use the Pololu universal mounting hub to mount custom wheels and mechanism to the micro metal gearmotor’s output shaft.
Pololu Wheel 32×7mm Pair - Black | Pololu Wheel 32×7mm Pair - White | Pololu Wheel 40×7mm Pair - Red |
Black Pololu Wheels with 90, 80, 70, 60, 40, and 32 mm diameters (other colors available). |
- Mounting Brackets: Our mounting bracket (also available in white) and extended mounting bracket are specifically designed to securely mount the gearmotor while enclosing the exposed gears. We recommend the extended mounting bracket for wheels with recessed hubs, such as the Pololu wheel 42×19mm.
- Quadrature Encoder: We offer a quadrature encoder for this motor that works with our extended bracket and 42×19mm wheel and provides feedback about wheel rotation (direction and speed). The encoder can be purchased as an individual unit or as part of an encoder set that includes two encoders, a pair of extended brackets, and a pair of 42×19mm wheels—just pick the particular micro metal gearmotor that best suits your application and you have a solution for closed-loop motor control.
- Motor Controllers: We have a number of motor controllers that make it easy to drive these micro metal gearmotors, including our qik 2s9v1 dual serial motor controller and our programmable Baby Orangutan and Orangutan SVP robot controllers. The inexpensive qik 2s9v1 allows variable speed and direction control of two small, brushed DC motors using a simple serial interface; the Orangutans combine a programmable Atmel AVR microcontroller and dual motor driver all in a single package and make interfacing with the motor drivers simple when you use our Pololu AVR library. All of the above controllers use the TB6612FNG dual motor driver, for which we also offer a simple carrier board.
DRV8838 Single Brushed DC Motor Driver Carrier. | Pololu A4990 Dual Motor Driver Shield for Arduino, bottom view. | DRV8835 dual motor driver carrier. |
Data sheet
- DC motor power
- LP
- Gear material
- Metal
- Gear ratio
- 150:1
- Rotation speed
- 90RPM
- Shaft diameter
- 3 mm
- Shaft shape
- D
- Obustronny wał silnika
- Tak
- Power supply voltage
- 6V
Other products in the same category (16)
15:1 Micro Metal Gearmotor. Pololu 4784
Small motor with metal gear and encoder, rotation speed 300 RPM, operating voltage 6 V. GA46-N20E-0048
Small, high power motor with 5: 1 metal gear, 12 V operating voltage, power consumption from 0.06 A to 0.75 A, speed 6800 RPM, maximum torque of 0.09 kg * cm, carbon brushes and double-sided shaft. Pololu 3047
No product available!
Small metal gear motor, 1000 RPM speed, 12V operating voltage. GA12-N20-0027
No product available!
15:1 Micro Metal Gearmotor. Pololu 4780
298:1 Micro Metal Gearmotor
A small, high-power motor with a 50: 1 metal gear, 6 V operating voltage, 0.1 A to 1.5 A power consumption, 650 RPM, a maximum torque of 0.74 kg * cm and carbon brushes with increased durability. Pololu 3063
No product available!
Small metal gear motor, 60 RPM speed, 6V operating voltage. GA12-N20-0013
Small metal gear motor, 20 RPM speed, 12V operating voltage. GA12-N20-0019
This gearmotor is a miniature high-power, 6 V brushed DC motor with long-life carbon brushes and a 9.96:1 metal gearbox. It has a cross section of 10 × 12 mm, and the D-shaped gearbox output shaft is 9 mm long and 3 mm in diameter.
A high-power miniature Pololu from the HP series. The motor with gear 210:1, shaft speed is 150rpm, torque is 3kg*cm (0.3Nm). The motor has an extended shaft which makes it easy to attach the encoder. Pololu 2216
No product available!
Pololu high power miniature motor with carbon brushes. 100:1 gear motor, shaft speed is 330 rpm, torque 1.6 kg*cm (0.16 Nm). Pololu 3065
Small metal gear motor, 60 RPM speed, 12V operating voltage. GA12-N20-0022
No product available!
Small motor with metal gear and encoder, rotation speed 50 RPM, operating voltage 6 V. GA46-N20E-0043
A small medium-power motor with a 30:1 metal gear, 6 V operating voltage, 0.04 A to 0.67 A power consumption, 720 RPM, a maximum torque of 0.33 kg*cm and a double-sided shaft. Pololu 2378
No product available!