Gravity: I2C ADS1115 16-Bit ADC Module - ADC converter module
ID: 571680
5902186313729
zł72.56
Tax included
zł58.99 tax excl.
Gravity: I2C ADS1115 The 16-Bit ADC Module is an analogue-to-digital converter module for Arduino and Raspberry Pi. This module uses 16-bit ADC ADS1115 and is powered by 3.3 ... 5V. DFRobot DFR0553
Description
Gravity: I2C ADS1115 The 16-Bit ADC Module is an analogue-to-digital converter module for Arduino and Raspberry Pi . This module uses 16-bit ADC ADS1115 and is powered by 3.3 ... 5 V. The system has a precise reference voltage and programmable gain control (PGA), so accurate collection and conversion can be performed for both permanent and very high variable signals.
One ADC module can read analog signals from 4 channels. Thanks to the built-in I2C address selection switch, it supports the connection of two ADC modules and can read analog signals from 8 channels. Thanks to this, it allows for a significant expansion of the capabilities of baseboards not equipped with a larger number of analog inputs.
Attention!
The voltage at the analog input contacts must be less than VCC + 0.3 V.
The voltage at the analog input contacts must be less than VCC + 0.3 V.
properties
- Analog detection range: 0 ... VCC
- Number of analogue channels: 4
- ADC resolution: 16 bits
- Interface: I2C
- Gravity connector
- Power consumption: 2 ... 3 mA
- Supply voltage: 3.3 ... 5 V
- Product size: 32 x 32 mm
Included
- Gravity module: I2C ADS1115 16-bit ADC
- Male goldpin connector (XH2.54-4pin)
- Connecting cable Gravity (Gravity-4P I2C / UART Sensor Wire)
571680
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
Module with 4-channel ADC ADS1115 converter. Equipped with a STEMMA QT connector, it communicates via the I2C interface. Adafruit 1085
zł77.77
Delivery date unknown
No product available!
Module with 4-channel ADC ADS1015 converter. Equipped with a STEMMA QT connector, it communicates via the I2C interface. Adafruit 1083
zł50.28
24h
Available quantity: 6
Available
Module with 8-bit ADC and 8-bit DAC. It allows you to measure voltage and generate an analog signal. Communicates via I2C. Adafruit 4648
zł33.59
24h
Available quantity: 2
Available
Other products in the same category (16)
8-channel module with current analog outputs ranging from 0 to 20 mA. It communicates via the RS485 interface and supports the Modbus RTU protocol. The board is enclosed in a housing that can be mounted on an industrial rail. Waveshare Modbus RTU Analog Output 8CH
zł87.12
24h
Available quantity: 12
Available
ADC converter module with 7 measurement channels (measuring 0-5V, 0-10V voltage and 4-20 mA current). Communicates via RS485 industrial interface using Modbus RTU protocol. R4AVA07
zł40.52
4 weeks
No product available!
I2S digital-to-analog converter based on the PCM5122, offering high-quality stereo line-level output, hardware mode operation and optional configuration via I2C or SPI, designed for microcontrollers and Raspberry Pi. Adafruit 6421
zł36.21
24h
Available quantity: 4
Available
A module with a 24-bit ADC converter HX711, which enables reading data from strain gauges and scales. The board is equipped with a Grove connector and communicates via a serial interface. Seeed Studio 101020712
zł19.10
4 weeks
No product available!
Extension module with ADC AD9250 converter dedicated to FPGA boards. It offers 4 input channels with a resolution of 14 bits and an ANSI/VITA 57.1 FMC connector. Numato Lab NLFMCADC001
zł6,785.09
3 weeks
No product available!
Module with 8-bit ADC and 8-bit DAC. It allows you to measure voltage and generate an analog signal. Communicates via I2C
zł6.42
4 weeks
No product available!
Module with 4-channel ADC ADS1115 converter. Equipped with a STEMMA QT connector, it communicates via the I2C interface. Adafruit 1085
zł77.77
4 weeks
No product available!
Gravity module designed based on the GP8101S system. It is a single-channel DAC (analog-to-digital) converter with PWM communication that offers an output signal with 8-bit resolution and 0.2% accuracy. It allows you to generate analog signals with a voltage range from 0 to 10 V or 0 to 5 V. DFRobot DFR1036
zł37.07
24h
Available quantity: 3
Available
Available
A module with a stereo DAC converter based on the UDA1334A chip. It can generate a signal with a resolution of 16, 20 or 24 bits. It communicates via the I2S interface. Adafruit 4037
zł70.16
4 weeks
No product available!
Demonstration board with Linear Technologies LTC2360 12-bit digital-to-analogue converter. The system is ideal for use in communication systems, data acquisition, mobile and car devices. DC1190A-E
Regular pricezł393.60zł309.96
24h
Available quantity: 2
Available
Audio module designed for Teensy 3.2, 3.5, 3.6 and 4.0. It uses the PT8211 16-bit digital to analog converter (DAC) chip. PJRC PT8211-AUDIO-KIT
zł17.32
24h
Available quantity: 5
Available
Expansion module with AD9763 DAC converter. It offers two channels with a resolution of 10 bits and processing speeds up to 125 MSPS. Numato Lab AD9763DAC01
zł235.05
3 weeks
No product available!
DAC converter module with current output in the range of 0 to 25 mA. It is powered by 18 V to 24 V and communicates via I2C interface (Gravity connector). It is used as a controller in industrial applications. DFRobot DFR0972
zł50.28
4 weeks
No product available!
Module with 12-bit DAC converter and built-in EEPROM memory. The module is supplied with the voltage from 2.7 to 5.5V, the I2C interface is used for communication. SparkFun BOB-12918
zł32.58
3 weeks
No product available!
Module with the driver of the resistive touch panel. Equipped with a STEMMA QT connector, it communicates via the I2C interface. Adafruit 5423
zł24.94
24h
Available quantity: 1
Available
Gravity: I2C ADS1115 The 16-Bit ADC Module is an analogue-to-digital converter module for Arduino and Raspberry Pi. This module uses 16-bit ADC ADS1115 and is powered by 3.3 ... 5V. DFRobot DFR0553