zł23.28 tax excl.
A module with a 24-bit ADC converter HX711, which allows you to read data from strain gauges and scales. It communicates via the serial interface. SparkFun SEN-13879
A module with a 24-bit ADC converter HX711, which allows you to read data from strain gauges and scales. It has a built-in programmable low-noise amplifier with optional gain of 32, 64 and 128. The HX711 chip integrates the power circuit, built-in clock oscillator and other peripheral circuits with fast response and noise immunity.
The load cells use a Wheatstone four-wire bridge configuration to connect to the HX711. These are RED, BLK, WHT, GRN and YLW colors, each of which corresponds to an encoding:
The YLW pin acts as an optional input that is not connected to a strain gauge, but is used for grounding and shielding against external electromagnetic interference (EMI).
The module communicates via the serial interface and is supplied with the voltage from 2.7 V to 5 V. Full documentation with examples of use is available on the product page.
Manufacturer
Responsible person
A module with a 24-bit ADC converter HX711, which allows you to read data from strain gauges and scales. It communicates via the serial interface. SparkFun SEN-13879
No product available!
DFRobot DFR0316
Dual 7-channel virtual sound adapter with USB 2.0 interface.
Gravity: I2C 12-Bit DAC is a module with 12-bit DAC and built-in EEPROM memory. The module is powered by 3.3 ... 5V for communication used by the I2C interface. DFRobot DFR0552
Gravity: I2C ADS1115 The 16-Bit ADC Module is an analogue-to-digital converter module for Arduino and Raspberry Pi. This module uses 16-bit ADC ADS1115 and is powered by 3.3 ... 5V. DFRobot DFR0553
4-channel ADC expansion board for Raspberry Pi, featuring a 16-bit Texas Instruments ADS1115 converter for measuring analog voltage signals. Supports four single-ended inputs or two differential inputs, programmable gain amplification (PGA), and conversion rates from 8SPS to 860SPS. Communicates via I2C at the default address 0x48, configurable to 0x49, 0x4A or 0x4B. Equipped with screw terminals and an analog Grove connector. Seeed Studio 103030279
Module with 24-bit ADC NAU7802 converter. It enables reading data from strain gauges and scales. I2C interface. SparkFun SEN-15242
No product available!
Module with 4-channel ADC ADS1015 converter. The system enables analog voltage conversion for both single signals (11-bit resolution) and differential signals (12-bit resolution). I2C communication. SparkFun DEV-15334
12-bit DAC converter module designed to work with the M5Stack sets. It enables the conversion of digital signals into an analog signal. M5Stack DAC Unit
A 16-bit DAC converter module designed to work with M5Stack sets. It enables the conversion of analog signals into a digital signal. M5Stack ADC Unit
Audio module based on a 32-bit PCM5102A DAC converter intended for cooperation, among others with Raspberry Pi minicomputers. Communication via the I2S interface. GY-PCM5102
A module with a 24-bit ADC converter HX711, which enables reading data from strain gauges and scales. The board is equipped with a Grove connector and communicates via a serial interface. Seeed Studio 101020712
Module with a 10-channel ADC ADS1263 converter with a resolution of 32-bits designed to work with the minicomputer Raspberry Pi and Jetson Nano. Waveshare High-Precision AD HAT
Audio module designed for Teensy 3.2, 3.5, 3.6 and 4.0. It uses the PT8211 16-bit digital to analog converter (DAC) chip. PJRC PT8211-AUDIO-KIT
A module with a 3-channel ADC ADC ADS1015, which allows you to read voltages from -24 V to +24 V with a sampling frequency of up to 3.3 kHz and a resolution of 12 bits. Pimoroni PIM422
Module with 4-channel 12-bit DAC MCP4728 converter with built-in EEPROM memory. Equipped with a STEMMA QT connector, it communicates using the I2C bus. Adafruit 4470
A module with a 24-bit ADC converter HX711, which allows you to read data from strain gauges and scales. It communicates via the serial interface. SparkFun SEN-13879