GM1008 - isolated 0-24mA to RS485 current signal converter

Expansion module with AD9763 DAC converter. It offers two channels with a resolution of 10 bits and processing speeds up to 125 MSPS. Numato Lab AD9763DAC01

Gravity: I2C ADS1115 The 16-Bit ADC Module is an analogue-to-digital converter module for Arduino and Raspberry Pi. This module uses 16-bit ADC ADS1115 and is powered by 3.3 ... 5V. DFRobot DFR0553

Gravity module designed based on the GP8503 system. It is a two-channel DAC (analog-to-digital) converter with I2C communication that offers an output signal with 12-bit resolution and 0.1% accuracy. It allows you to generate analog signals with a voltage range from 0 to 2.5 V or from 0 to VCC. DFRobot DFR1034

3-channel voltage and current monitoring module designed to work with the Raspberry Pi. It can measure voltage ranging from 0 to 26 V and voltage ± 3.2 A. SB Components 20805

A module with a stereo DAC converter based on the UDA1334A chip. It can generate a signal with a resolution of 16, 20 or 24 bits. It communicates via the I2S interface. Adafruit 4037

Module with 4-channel 12-bit DAC MCP4728 converter with built-in EEPROM memory. Equipped with a STEMMA QT connector, it communicates using the I2C bus. Adafruit 4470

A module with a 24-bit ADC converter HX711, which allows you to read data from strain gauges and scales. It communicates via the serial interface. SparkFun SEN-13879

Module with 4-channel ADC ADS1015 converter. The system enables analog voltage conversion for single signals and differential signals with 12-bit resolution. I2C communication

Module with 4-channel ADC ADS1115 converter. The system enables analog voltage conversion for single signals and differential signals with 16-bit resolution. I2C communication

8-channel module with current analog outputs ranging from 0 to 20 mA. It communicates via the RS485 interface and supports the Modbus RTU protocol. The board is enclosed in a housing that can be mounted on an industrial rail. Waveshare Modbus RTU Analog Output 8CH

Extension module with ADC AD9250 converter dedicated to FPGA boards. It offers 4 input channels with a resolution of 14 bits and an ANSI/VITA 57.1 FMC connector. Numato Lab NLFMCADC001

Gravity module designed based on the GP8101S system. It is a single-channel DAC (analog-to-digital) converter with PWM communication that offers an output signal with 8-bit resolution and 0.2% accuracy. It allows you to generate analog signals with a voltage range from 0 to 10 V or 0 to 5 V. DFRobot DFR1036

Gravity module designed based on the GP8413 system. It is a two-channel DAC (analog-to-digital) converter with I2C communication that offers an output signal with a resolution of 15-bit and an accuracy of 0.2%. It allows you to generate analog signals with a voltage range from 0 to 10 V or 0 to 5 V. DFRobot DFR1073

High-quality digital-to-analog converter that allows for pure stereo audio playback without the need for I2C configuration or the MCLK pin. It supports I2S signals (BCLK, WSEL, DIN) and audio formats up to 32 bits and 384 kHz, providing an excellent signal-to-noise ratio (112 dB). Audio output is available via a 3.5 mm jack or on-board pads, and the module works best as a line output to amplifiers and audio systems. Adafruit 6250

Module with 8 voltage analog outputs with a range from 0 to 10 V. It communicates via the RS485 interface and supports communication within the Modbus RTU protocol. The board is enclosed in a housing that can be mounted on an industrial rail. Waveshare Modbus RTU Analog Output 8CH (B)

DFRobot DFR0316