DC1190A-E - set with A / C LT2360 transducer

High-quality digital-to-analog converter that allows for pure stereo audio playback without the need for I2C configuration or the MCLK pin. It supports I2S signals (BCLK, WSEL, DIN) and audio formats up to 32 bits and 384 kHz, providing an excellent signal-to-noise ratio (110 dB). Audio output is available via a 3.5 mm jack or on-board pads, and the module works best as a line output to amplifiers and audio systems. Adafruit 6251

A 16-bit DAC converter module designed to work with M5Stack sets. It enables the conversion of analog signals into a digital signal. M5Stack ADC Unit

Module with a 10-channel ADC ADS1263 converter with a resolution of 32-bits designed to work with the minicomputer Raspberry Pi and Jetson Nano. Waveshare High-Precision AD HAT

ADC converter module with 7 measurement channels (measuring 0-5V, 0-10V voltage and 4-20 mA current). Communicates via RS485 industrial interface using Modbus RTU protocol. R4AVA07

Module with 4-channel 12-bit DAC MCP4728 converter with built-in EEPROM memory. Equipped with a STEMMA QT connector, it communicates using the I2C bus. Adafruit 4470

Module with 4-channel ADC ADS1015 converter. The system enables analog voltage conversion for single signals and differential signals with 12-bit resolution. I2C communication

Audio module based on a 32-bit PCM5102A DAC converter intended for cooperation, among others with Raspberry Pi minicomputers. Communication via the I2S interface. GY-PCM5102

Audio expansion module with CS4344 24-bit DAC converter. Numato Lab EXPAUD002

Module with an 8-channel ADC converter with 8-bit resolution. It uses the ADS7830 chip and is equipped with a STEMMA QT connector, thanks to which it communicates via the I2C interface. Adafruit 5836

Module with 24-bit ADC NAU7802 converter. It enables reading data from strain gauges and scales. I2C interface. SparkFun SEN-15242

Gravity module designed based on the GP8503 system. It is a two-channel DAC (analog-to-digital) converter with I2C communication that offers an output signal with 12-bit resolution and 0.1% accuracy. It allows you to generate analog signals with a voltage range from 0 to 2.5 V or from 0 to VCC. DFRobot DFR1034

Module with 4-channel ADC ADS1015 converter. Equipped with a STEMMA QT connector, it communicates via the I2C interface. Adafruit 1083

Module with 8 inputs for data acquisition from 0-24 mA analog current inputs. It communicates via RS485 interface and supports Modbus RTU protocol. The board is enclosed in an industrial enclosure. GM1008

A module with a stereo DAC converter based on the UDA1334A chip. It can generate a signal with a resolution of 16, 20 or 24 bits. It communicates via the I2S interface. Adafruit 4037

High-quality digital-to-analog converter that allows for pure stereo audio playback without the need for I2C configuration or the MCLK pin. It supports I2S signals (BCLK, WSEL, DIN) and audio formats up to 32 bits and 384 kHz, providing an excellent signal-to-noise ratio (112 dB). Audio output is available via a 3.5 mm jack or on-board pads, and the module works best as a line output to amplifiers and audio systems. Adafruit 6250

Extension module with ADC AD9250 converter dedicated to FPGA boards. It offers 4 input channels with a resolution of 14 bits and an ANSI/VITA 57.1 FMC connector. Numato Lab NLFMCADC001