Modbus RTU Analog Output 8-channel module 0-20 mA with RS485 interface - Waveshare 26419

A compact board with eight 12-bit DACs that allow precise voltage control on each output via I2C communication. Compatible with 3.3V or 5V, it offers flexibility with a reference voltage setting and STEMMA QT or Qwiic connectors for easy integration with other I2C devices. Adafruit 6223

Gravity: I2C ADS1115 The 16-Bit ADC Module is an analogue-to-digital converter module for Arduino and Raspberry Pi. This module uses 16-bit ADC ADS1115 and is powered by 3.3 ... 5V. DFRobot DFR0553

High-quality digital-to-analog converter that allows for pure stereo audio playback without the need for I2C configuration or the MCLK pin. It supports I2S signals (BCLK, WSEL, DIN) and audio formats up to 32 bits and 384 kHz, providing an excellent signal-to-noise ratio (110 dB). Audio output is available via a 3.5 mm jack or on-board pads, and the module works best as a line output to amplifiers and audio systems. Adafruit 6251

A module with a 3-channel ADC ADC ADS1015, which allows you to read voltages from -24 V to +24 V with a sampling frequency of up to 3.3 kHz and a resolution of 12 bits. Pimoroni PIM422

Gravity: I2C 12-Bit DAC is a module with 12-bit DAC and built-in EEPROM memory. The module is powered by 3.3 ... 5V for communication used by the I2C interface. DFRobot DFR0552

3-channel voltage and current monitoring module designed to work with the Raspberry Pi. It can measure voltage ranging from 0 to 26 V and voltage ± 3.2 A. SB Components 20805

Gravity module designed based on the GP8413 system. It is a two-channel DAC (analog-to-digital) converter with I2C communication that offers an output signal with a resolution of 15-bit and an accuracy of 0.2%. It allows you to generate analog signals with a voltage range from 0 to 10 V or 0 to 5 V. DFRobot DFR1073

Module with 12-bit DAC converter and built-in EEPROM memory. The module is supplied with the voltage from 2.7 to 5.5V, the I2C interface is used for communication. SparkFun BOB-12918

DFRobot DFR1184 module with a 15-bit ADS1115 converter enables precise voltage measurements of 0–10 V from industrial sensors. The dual-channel design, support for I2C/UART, and compatibility with popular platforms make it an effective solution for automation systems, environmental monitoring, and energy management.

Dual-channel DAC converter compatible with the SYZYGY standard. The module can simultaneously generate two 5V signals with 14-bit resolution and sampling frequency up to 100MS/s. The module is compatible with Eclypse Z7 and Genesys ZU evaluation kits. Digilent Zmod AWG 1411 410-397

Module with 16-bit AD5693R DAC converter with built-in EEPROM memory. Equipped with a STEMMA QT connector, it communicates using the I2C bus. Adafruit 5811

Extension module with ADC AD9250 converter dedicated to FPGA boards. It offers 4 input channels with a resolution of 14 bits and an ANSI/VITA 57.1 FMC connector. Numato Lab NLFMCADC001

Gravity module designed based on the GP8211 system. It is a single-channel DAC (analog-to-digital) converter with I2C communication that offers an output signal with a resolution of 15-bit and an accuracy of 0.01%. It allows you to generate analog signals with a voltage range from 0 to 10 V or 0 to 5 V. DFRobot DFR1071

Module with an 8-channel ADC converter with 8-bit resolution. It uses the ADS7830 chip and is equipped with a STEMMA QT connector, thanks to which it communicates via the I2C interface. Adafruit 5836

Gravity module designed based on the GP8512 system. It is a single-channel DAC (analog-to-digital) converter with I2C communication that offers an output signal with a resolution of 15-bit and an accuracy of 0.01%. It allows you to generate analog signals with a voltage range from 0 to 2.5 V or from 0 to VCC. DFRobot DFR1035

A module with a 24-bit ADC converter HX711, which enables reading data from strain gauges and scales. The board is equipped with a Grove connector and communicates via a serial interface. Seeed Studio 101020712