 
        
           
        
          Module with a 4-channel ADC ADS1015 converter, which allows you to read voltages in a single signal mode or differential signals with a sampling frequency of up to 3.3 kHz and a resolution of 12 bits. It is ideally suited for fast and precise DC voltage measurement over a wide range. It has a built-in programmable amplifier (up to x16), allowing you to amplify low-amplitude signals to the full range. The module is compatible with 3.3 V and 5 V controllers, and communication is via the I2C interface (STEMMA QT connector). Full documentation is available on the product page.
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
A set of 40 pieces of female-female connecting cables in various colors, 10 cm long
A set of 40 pcs of male-female connecting cables in various colors, 10 cm long
A set of 40 pcs of male-male connecting cables in various colors, 10 cm long
4-wire cable with a length of 50 mm. Both ends with STEMMA QT (Qwiic) plug. Adafruit 4399
4-wire cable with a length of 100 mm. Both ends with STEMMA QT (Qwiic) plug. Adafruit 4210
4-core cable with a length of 200 mm. Both ends with STEMMA QT (Qwiic) plug. Adafruit 4401
A module with a stereo DAC converter based on the UDA1334A chip. It can generate a signal with a resolution of 16, 20 or 24 bits. It communicates via the I2S interface. Adafruit 4037
 No product available!
Module with 8 inputs for data acquisition from 0-24 mA analog current inputs. It communicates via RS485 interface and supports Modbus RTU protocol. The board is enclosed in an industrial enclosure. GM1008
A 2-channel DAC converter module with an output voltage range from 0 to 10 V. It is powered by 3.3 V to 5 V and communicates via I2C interface (Gravity connector). It is used as a controller in industrial applications. DFRobot DFR0971
Gravity module designed based on the GP8501 system. It is a two-channel DAC (analog-to-digital) converter with PWM communication that offers an output signal with 8-bit resolution and 0.5% accuracy. It allows you to generate analog signals with a voltage range from 0 to 2.5 V or from 0 to VCC. DFRobot DFR1037
Extension module with ADC AD7616 converter dedicated to FPGA boards. It offers 32 channels with a resolution of 16 bits and an FMC LPC connector. Numato Lab NLFMCADC002
 No product available!
Module with 4-channel ADC ADS1115 converter. The system enables analog voltage conversion for single signals and differential signals with 16-bit resolution. I2C communication
ADC converter module with 7 measurement channels (measuring 0-5V, 0-10V voltage and 4-20 mA current). Communicates via RS485 industrial interface using Modbus RTU protocol. R4AVA07
 No product available!
Audio module based on a 32-bit PCM5102A DAC converter intended for cooperation, among others with Raspberry Pi minicomputers. Communication via the I2S interface. GY-PCM5102
Audio module designed for Teensy 3.2, 3.5, 3.6 and 4.0. It uses the PT8211 16-bit digital to analog converter (DAC) chip. PJRC PT8211-AUDIO-KIT
Module with 24-bit ADC NAU7802 converter. It enables reading data from strain gauges and scales. I2C interface. SparkFun SEN-15242
Expansion module with AD9763 DAC converter. It offers two channels with a resolution of 10 bits and processing speeds up to 125 MSPS. Numato Lab AD9763DAC01
 No product available!
Gravity module designed based on the GP8211 system. It is a single-channel DAC (analog-to-digital) converter with I2C communication that offers an output signal with a resolution of 15-bit and an accuracy of 0.01%. It allows you to generate analog signals with a voltage range from 0 to 10 V or 0 to 5 V. DFRobot DFR1071
Gravity module designed based on the GP8101S system. It is a single-channel DAC (analog-to-digital) converter with PWM communication that offers an output signal with 8-bit resolution and 0.2% accuracy. It allows you to generate analog signals with a voltage range from 0 to 10 V or 0 to 5 V. DFRobot DFR1036
8-channel module with current analog outputs ranging from 0 to 20 mA. It communicates via the RS485 interface and supports the Modbus RTU protocol. The board is enclosed in a housing that can be mounted on an industrial rail. Waveshare Modbus RTU Analog Output 8CH
A module with a 24-bit differential ADC NAU7802 optimized for reading strain gauges in a Wheatstone bridge configuration. It offers high precision force or mass measurements. Thanks to the I2C interface, ready-made libraries and screw connectors, it is easy to integrate, especially in mobile and DIY projects. Adafruit 4538
 No product available!
 
                    Module with 4-channel ADC ADS1015 converter. Equipped with a STEMMA QT connector, it communicates via the I2C interface. Adafruit 1083