STEMMA QT AD5693R Breakout - module with 16-bit DAC converter
ID: 1188205
5906623431878
zł57.47
Tax included
zł46.72 tax excl.
Module with 16-bit AD5693R DAC converter with built-in EEPROM memory. Equipped with a STEMMA QT connector, it communicates using the I2C bus. Adafruit 5811
Description
DAC converter module based on the AD5693R chip, which offers amazing 16-bit resolution. This means you can precisely control the output voltage, which is ideal for advanced applications. The DAC converter works with both 3.3V and 5V. Moreover, you have full control over the maximum output voltage. You can set them to 2.5V or 5V (2 times Vref). This gives you the flexibility to adapt the module to the requirements of your project. If you power it with 3.3V, the output range is 0 to 3.3V.
The converter supports a fast I2C bus with a speed of 3.4 Mbps, which allows the output voltage to be updated with a frequency of approximately 200 kHz. Thanks to the EEPROM memory, you can save the set output voltage and even after turning off the power, the module restores the stored voltage. Additionally, the module has an ADDR pin that allows you to configure the I2C address. This allows you to connect two DAC converter modules to one bus. All this makes the DAC converter module an excellent tool for advanced applications that require accurate voltage control.
Features
- AD5693R chip
- High relative accuracy (INL): maximum ±2 LSB at 16 bits
- Low drift, 2.5V reference voltage: 2 ppm/°C typical
- Selectable output range: 2.5 V or 5 V
- Total Uncorrected Error (TUE): ±0.06% of the maximum FSR value
- Offset error: ±1.5 mV maximum
- Gain error: ±0.05% of maximum FSR
- Low error: 0.1 nV-sec
- Current capacity: 20 mA
- I2C interface
- STEMMA QT connector
- Wide operating temperature range: from -40°C to +105°C
- Dimensions: 25.2 x 17.6 x 4.8 mm
Kit contains
- STEMMA QT AD5693R Breakout module
- Goldpin male straight 8-pin connector
1188205
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
4-wire cable with a length of 50 mm. Both ends with STEMMA QT (Qwiic) plug. Adafruit 4399
zł5.98
24h
Available quantity: 30
Available
4-wire cable with a length of 100 mm. Both ends with STEMMA QT (Qwiic) plug. Adafruit 4210
zł5.29
24h
Available quantity: 1
Available
4-core cable with a length of 200 mm. Both ends with STEMMA QT (Qwiic) plug. Adafruit 4401
zł7.69
24h
Available quantity: 8
Available
4-core cable with a length of 300 mm. Both ends with STEMMA QT (Qwiic) plug. Adafruit 5384
zł9.90
Delivery date unknown
No product available!
Other products in the same category (16)
Module with 3-axis ADXL375 accelerometer with a wide measurement range up to ±200g. The board is equipped with a STEMMA QT connector and communicates via the I2C or SPI interface. Adafruit 5374
zł124.18
24h
Available quantity: 4
Available
Module with light sensor VEML7700. It allows you to measure the intensity in the range from 0 to 120 Klx. Equipped with a STEMMA QT connector, it communicates via the I2C interface. Adafruit 5378
zł24.24
24h
Available quantity: 1
Available
Module with audio amplifier and 8 Ω speaker with a power of 1 W. The board is equipped with a STEMMA connector. Adafruit 3885
zł31.28
4 weeks
No product available!
Module with ToF VL53L4CD sensor with a range of up to 1.3 m and a resolution of 1 mm. It is equipped with a STEMMA QT connector and communicates via the I2C interface. Adafruit 5396
zł76.14
24h
Available quantity: 1
Available
Module with ToF VL53L4CX sensor with a range of up to 6 m. It is equipped with a STEMMA QT connector and communicates via the I2C interface. Adafruit 5425
zł84.14
24h
Available quantity: 2
Available
Module with 6-axis IMU sensor that allows you to measure acceleration and rotational speed in the range up to ±16g and ±2000dps. Equipped with a STEMMA QT connector, it communicates via I2C or SPI. Adafruit 4503
zł47.38
4 weeks
No product available!
Module with a 3-axis magnetic field sensor MMC5603. Equipped with a STEMMA QT connector, it communicates via the I2C interface. Adafruit 5579
zł28.82
24h
Available quantity: 4
Available
The module with the I2C controller based on the HT16K33 system. Dedicated to 14-segment displays. It is equipped with STEMMA QT connectors. Adafruit 1910
zł30.23
24h
Available quantity: 5
Available
Module with a monitor of the operation of LiPo/Li-Ion batteries based on the MAX17048 system. It allows you to measure the voltage and state of charge of the battery. Adafruit 5580
zł31.96
24h
Available quantity: 4
Available
Module with a light intensity sensor LTR-329. It offers a measuring range from 1 to 65535 lux and a 16-bit resolution. Communication takes place using I2C. Adafruit 5591
zł27.13
4 weeks
No product available!
Module with light intensity sensor LTR-303. It offers a measuring range from 1 to 65535 lux and a 16-bit resolution. Communication takes place using I2C. Adafruit 5610
zł28.39
4 weeks
No product available!
zł12.73
24h
Available quantity: 3
Available
Module with ENS160 gas sensor for measuring the concentration of carbon dioxide (eCO2) and volatile organic compounds (TVOC) in the air. It communicates via the I2C or SPI interface. Adafruit 5606
zł129.42
24h
Available quantity: 1
Available
Module with 16-channel PCF8575 IO expander controlled by the I2C interface. Equipped with a STEMMA QT connector. Adafruit 5611
zł29.99
24h
Available quantity: 3
Available
Module with a voltage level converter from 5 V to 3.3 V, intended for use in the STEMMA QT/Qwiic system. It has a built-in voltage stabilizer providing 3.3 V power supply with a current of up to 500 mA. Adafruit 5637
zł15.13
24h
Available quantity: 5
Available
Clock signal generator with a frequency of 8 kHz to 160 MHz based on the SI5351A integrated circuit. Communication with the module takes place via the I2C bus. Adafruit 5640
zł41.21
24h
Available quantity: 3
Available
Module with 16-bit AD5693R DAC converter with built-in EEPROM memory. Equipped with a STEMMA QT connector, it communicates using the I2C bus. Adafruit 5811