

A module with a 3-axis magnetic field sensor MMC5603 dedicated to measuring the Earth's magnetic field. It allows you to detect magnetic north. The sensor is usually combined with an accelerometer and a 6 DoF gyroscope to create a 9-DoF inertial measurement unit that can detect its orientation in space. It is powered with the voltage from 3.3 V to 5 V, and communication is via the I2C interface (STEMMA QT connector). Full documentation is available on the product page.
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
4-wire cable with a length of 50 mm. Both ends with STEMMA QT (Qwiic) plug. Adafruit 4399
4-wire cable with a length of 100 mm. Both ends with STEMMA QT (Qwiic) plug. Adafruit 4210
4-core cable with a length of 200 mm. Both ends with STEMMA QT (Qwiic) plug. Adafruit 4401
Cable with a length of 150 mm, on one side terminated with a female STEMMA QT (Qwiic) connector, and on the other side with single female goldpin connectors. Adafruit 4397
Cable with a length of 150 mm, on one side terminated with a female STEMMA QT (Qwiic) connector, and on the other side with single male goldpin connectors. Adafruit 4209
Module with TLV493D 3-axis magnetic field sensor. Equipped with a STEMMA QT connector, it communicates via the I2C interface. Adafruit 4366
PmodCMPS2 is a module with a digital magnetometer based on the Memsic MMC34160PJ system. It has a resolution of 0.5 mG (within ± 16) and accuracy up to 1 °. For communication with the module, an I2C interface is provided on the 6-pin Pmod connector. Digilent 410-355
No product available!
Precise Hall effect sensor that converts magnetic field intensity into analog voltage. Differential response to magnetic poles (voltage increases when approaching S pole and decreases at N pole) enables precise analysis of field direction and strength. High sensitivity, low noise and compatibility with platforms such as Arduino and micro:bit make the sensor ideal for industrial, educational and hobby applications. DFRobot DFR1132
Module with a 3-axis magnetic field sensor LIS3MDL. Equipped with a STEMMA QT connector, it communicates via the I2C interface. Adafruit 4479
KAmodMAG3110FC is a module with magnetic field sensor MAG3110FC from NXP. The sensor measures the magnetic field in the range of ±1000μT, with a resolution of 0.1μT. Communication with the sensor is realized via the I2C interface. The board is equipped with the Pmod I2C standard connector and the KAMAMI connector. Kamami KAmodMAG3110FC
Advanced electronic compass module that precisely calculates direction to within a few degrees, and its tilt compensation allows operation in difficult environmental conditions. The module is easy to use and allows to obtain measurement data via I2C interface at 5 Hz. SparkFun SEN-12916
No product available!
Precise, 3-axis geomagnetic sensor based on FlipCore and TMR technology, offering high interference immunity and a wide measurement range of ±2000μT with a resolution of 0.1μT. Thanks to its high sampling rate (up to 400Hz) and resistance to magnetic shocks, it is ideal for AR/VR systems, AGV navigation and drone control. DFRobot SEN0622
Complete kit for building a gradiometer, including two FG-3+ magnetometer sensors, a PCB board, Android-enabled software, and a mobile app. The kit allows for easy assembly and quick start-up of the device, which will immediately start displaying readings on the LCD after connection. Additional accessories, such as sensor holders, sensor tuning pipes, and a housing, provide convenience, safety, and precise adjustment of the device to use. SparkFun WIG-25530
No product available!
A sensitive sensor of the magnetic field, operating in the range of ± 50 microtesels, which generates a rectangular signal proportional to the strength of the field, which facilitates its integration with microcontrollers. It is distinguished by high temperature stability and tenderness, which makes it ideal for precise magnetic field measurements in applications requiring reliability. Sparkfun Sen-25531
No product available!
Precise 3-axis compass based on FlipCore and TMR technology, offering magnetic field measurement in the range of ±2000μT without the need for calibration. With I3C support, sampling rate up to 400 Hz and Field Shock Recovery function, it is perfect for navigation systems, AR/VR, drones and autonomous vehicles. DFRobot SEN0619
HMC5883L digital electronic compass 3-axis magnetoresistive sensor module with level converter, RoHS
Pololu - 2737
The GY‑271 module with HMC5883L sensor is a precise digital compass offering three-axis magnetic field measurement, I²C communication, and 3 V–5 V operation. Suitable for robotics, navigation, and embedded systems requiring low power consumption and a compact form factor. GY‑271
A module with a 3-axis magnetometer based on the BMM150 chip. It communicates via an I2C interface. DFRobot SEN0529
Module with a 3-axis magnetometer based on the MLX90393 system. It has a measuring range from ± 5mT to ± 50mT and a resolution of 0.161 µT. The I2C or SPI interface is used for communication. Adafruit 4022
Module with 3-axis digital compass, HMC5983, I2C, SPI, RoHS
Module with a 3-axis magnetic field sensor MMC5603. Equipped with a STEMMA QT connector, it communicates via the I2C interface. Adafruit 5579