zł10.34 tax excl.
A module with a magnet sensor that allows you to detect the presence of an object emitting a magnetic field in the environment. The module is supplied with the voltage ranging from 3.3 V to 5 V and has a digital output. DFrobot DFR0033
A module with a magnet sensor that allows you to detect the presence of an object emitting a magnetic field in the environment. The module is powered with the voltage ranging from 3.3 V to 5 V and has a digital output (Gravity connector). There is also an indicator diode on the board. An instruction and a sample program are available on the Wiki page.
Manufacturer
Responsible person
Arduino Uno Rev3 is a popular board with Atmel ATmega328 microcontroller from the AVR family, there are 14 I / O lines, 6 PWM channels and 6 analog inputs. The additional ATmega16U4 microcontroller realizes communication via the USB interface. Arduino A000066
Expansion board for Arduino, allows easy connection of XBee modules, has separate outputs for I2C, SPI and UART buses. The built-in 3.3V voltage stabilizer and operating mode switch make it easier to program the Arduino when the XBee module is connected to the sockets. DFRobot DFR0265
Board with ATmega1280 microcontroller from the AVR family, the user has 54 I/O lines, 14 PWM channels, 16 analog inputs. DFRobot DFR0003
No product available!
Gravity I2C OLED-2864 Display is an OLED display with I2C interface with 128x64 resolution, powered by 3.3-5V. DFRobot DFR0486
No product available!
Nano I / O Shield for Arduino Nano is an expansion board for Arduino Nano that provides digital, analog pins, power inputs and a connector for the Bluetooth module. DFRobot DFR0012
BME280 integrates onboard temperature sensor, humidity sensor and barometer. It provides both SPI and I2C interfaces; and can be widely used in environmental monitoring, story height measurement and Internet of Things (IoT) control and so on. SEN0236
DFRobot 315MHz RF receiver module using SC2272-L4 low power decoder chip. DFRobot TEL0112
DFR0464
Gravity: I2C VEML7700 Ambient Light. Sensor SKU. SEN0228
No product available!
Gravity Colorful LED is an LED twinkles with seven colors--the colors of rainbow. DFRobot DFR0474
Clock & Timer Development Tools Gravity I2C SD2405 RTC. DFR0469
Gravity: Analog Signal Isolator is a module that allows to isolate sensors in the system and eliminate mutual interference of sensors powered by 5V. DFRobot DFR0504
Module 4-pin sensor adapter. DFRobot FIT0511
Measurement module for dissolved oxygen in water. It allows you to determine the level of water quality. The set includes a measuring module and a probe. DFRobot SEN0237-A
Expansion board for micro:bit modules with connectors compatible with Boson and Gravity sets. DFRobot DFR0521
Audio Analyzer is a module with sound analyzer based on the MSGEQ7 system. It divides the sound into seven frequency bands, and then allows you to read the peak levels of each band. It allows you to measure the sound in the following frequencies: 63Hz, 160Hz, 400Hz, 1kHz, 2.5kHz, 6.25kHz and 16kHz. DFRobot DFR0126
The expansion board is designed for DFRduino M0 or Bluno M0 sets. The board has 31 GPIO pins (including 6 PWM and 6 ADC inputs), UART, I2C and SPI interfaces. The pins are color coded according to the Gravity standard. DFRobot DFR0412
A module with an EMG sensor that detects the activity of human muscles and neurons. Generates an analog signal in the range from 0 to 3 V on the output, it does not require the use of a conductive gel. DFRobot SEN0240
Gravity: Analog TDS Sensor / Meter is an analog water purity measurement module. It is powered by 3.3 ... 5.5V voltage and has an analogue output interface. Module compatible with Arduino. DFRobot SEN0244
A module with a magnet sensor that allows you to detect the presence of an object emitting a magnetic field in the environment. The module is supplied with the voltage ranging from 3.3 V to 5 V and has a digital output. DFrobot DFR0033