

VEML7700 is a high accuracy ambient light digital 16-bit resolution sensor. It includes a high sensitive photo diode, a low noise amplifier, a 16-bit A/D converter and supports an easy to use Gravity I2C interface. It outputs a digital signal directly and no need for complicated calculations. This is a more accurate and easier to use version of the simple photo resistor which only outputs a voltage that needs to be calculated in order to obtain meaningful data. The data which is output by this sensor is directly output in Lux (Lx). When objects which are lighted in homogeneous get the 1 lx luminous flux in one square meter, their light intensity is 1lx. Sometimes to take good advantage of the illuminant, you can add a reflector to the illuminant. So that there will be more luminous flux in some directions and it can increase the illumination of the target surface.
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
modTSL2561 is a module containing a light sensor TSL2561; communication with the system takes place using the I2C bus
The module allows measuring the light around the sensor. The measuring range is in the range 1 - 65535 LUX, and communication takes place using the I2C bus. modBH1750 (GY-302)
Great way to upgrade a project that uses a photocell and needs RoHS compliance. Due to the high rejection ratio of infrared radiation, the spectral response of the ambient light sensor is close to that of human eyes. Adafruit 2748
Expansion board for Arduino, allows easy connection of XBee modules, has separate outputs for I2C, SPI and UART buses. The built-in 3.3V voltage stabilizer and operating mode switch make it easier to program the Arduino when the XBee module is connected to the sockets. DFRobot DFR0265
Module with an analog TEMT6000 light intensity sensor. The output voltage increases with the intensity of the incident light. The sensor is powered with the voltage of 5 V
Precise solar radiation intensity sensor in the range from 400 to 1100 nm, communicating via Modbus-RTU (RS485) and resistant to harsh conditions thanks to the aluminum housing class IP67. High accuracy (±5%), fast response time (≤10 s) and resistance to dirt make it ideal for monitoring photovoltaics, environmental research and meteorology. DFRobot SEN0640
No product available!
Light sensor module in the form of a photoresistor. A comparator and a potentiometer are placed on the board. The module has a digital output
Gravity: High Accuracy is a multifunctional environmental sensor with Gravity I2C and UART output. Perfect for weather station projects. DFRobot SEN0501
Module with environmental sensors for Raspberry Pi Pico. It allows you to measure temperature, humidity, air quality pressure and color detection. SB Components 22366
Module with light sensor VEML7700. It allows you to measure the intensity in the range from 0 to 120 Klx. Equipped with a STEMMA QT connector, it communicates via the I2C interface. Adafruit 5378
Precision XYZ color and light sensor with I2C interface. Measures light intensity and color components, features STEMMA QT / Qwiic connectors. Adafruit 6335
Multi-functional environmental sensor consisting of SHTC3 temperature and humidity sensor, BMP280 pressure sensor, VEML7700 ambient light sensor and ML8511 UV sensor. DFRobot SEN0500
Module with a UV light sensor LTR390-UV. It allows you to measure the intensity of ultraviolet radiation and visible light. It communicates via the I2C interface. Waveshare UV Sensor (C)
Module with a light intensity sensor LTR-329. It offers a measuring range from 1 to 65535 lux and a 16-bit resolution. Communication takes place using I2C. Adafruit 5591
Module with a light intensity sensor BH1750FVI dedicated to the M5StickC sets. It communicates via the I2C interface. M5Stack U134
No product available!
AS7331 UV light sensor module. It allows you to measure UV radiation on three channels: UVA (320-400nm), UVB (280-320nm) and UVC (200-280nm). Communication with AS7331 takes place via the I2C interface and the Qwiic connector. SparkFun SEN-23517
Module with a UV light sensor LTR390-UV. It allows you to measure the intensity of ultraviolet radiation and visible light. Equipped with a STEMMA QT connector, it communicates via the I2C interface. Adafruit 4831
Sensor for detecting the distance, intensity and frequency of light (lightning) within a radius of 40 km. The module enables weather enthusiasts to measure data about local storms. DFRobot SEN0290
Module with a light sensor based on the APDS-9002 system. With the aid of this system, it is possible to measure the intensity of illumination in lux. The module has a connector in accordance with the Grove standard. Seeed studio 101020076
Gravity: I2C VEML7700 Ambient Light. Sensor SKU. SEN0228