

The SparkFun AS7262 Visible Spectral Sensor Breakout brings spectroscopy to the palm of your hand, making it easier than ever to measure and characterize how different materials absorb and reflect different wavelengths of light. The AS7262 Breakout is unique in its ability to communicate by both an I2C interface and serial interface using AT commands. Hookup is easy, thanks to the Qwiic connectors attached to the board — simply plug one end of the Qwiic cable into the breakout and the other into one of the Qwiic Shields, then stack the board on a development board. You’ll be ready to upload a sketch to start taking spectroscopy measurements in no time.
The AS7262 spectrometer detects wavelengths in the visible range at 450, 500, 550, 570, 600 and 650nm of light each with 40nm of full-width half-max detection. The board also has multiple ways for you to illuminate objects that you will try to measure for a more accurate spectroscopy reading. There is an onboard LED that has been picked out specifically for this task, as well as two pins to solder your own LED into.
The SparkFun Qwiic Connect System is an ecosystem of I2C sensors, actuators, shields and cables that make prototyping faster and less prone to error. All Qwiic-enabled boards use a common 1mm pitch, 4-pin JST connector. This reduces the amount of required PCB space, and polarized connections mean you can’t hook it up wrong
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
No product available!
KAmodVL6180X is a module that allows to measure light intensity (ALS), distance to the object and recognition of gesture. It has an embedded voltage regulator and voltage level translators on signal lines. Thanks to this can be used in systems with 2.8...5.5V power supply voltage.
Color sensor equipped with the OPT4048 sensor from Texas Instruments. It allows you to determine the characteristics of ambient light by measuring parameters such as light intensity, color in the CIE XY, LUV coordinate systems, as well as color temperature. The module is equipped with Qwiic connectors. SparkFun SEN-22639
No product available!
A multifunctional module with an optical sensor for measuring the intensity of illumination, the color of the incident RGB light, the distance from the object and the detection of 3D gestures. Detection range from 10 to 20 cm, communication via I2C. SparkFun SEN-12787
No product available!
Module with a light sensor (photoresistor) designed for M5Stack sets. An analog output and a digital output have been led out on the Grove connector. M5Stack U021
Module with 11-channel AS7341 sensor that allows to detect light in different wavelength ranges (color detection). It communicates via the I2C interface. Waveshare AS7341 Spectral Color Sensor
Color Sensor, complete color detector
Heart rate monitor module based on the popular MAX30101 chip. The board is equipped with connectors compliant with the Qwiic standard. SparkFun SEN-16474
No product available!
DFRobot Gravity analog light intensity module for Arduino and Raspberry Pi. DFRobot DFR0026
Module with color and light intensity sensor. Offers a wide detection range and two LED backlights. It communicates via the I2C bus. It communicates via the I2C bus. Pimoroni PIM375
No product available!
LTR390-UV UV light sensor module. Allows measurement of ultraviolet and visible light intensity. Equipped with a Gravity connector, it communicates via an I2C or UART interface. DFRobot SEN0540
UV Sensor with response spectrum: 200nm-370nm
ireless sensor with LoRaWAN network communication. Dedicated to industrial long-distance data acquisition with a wide light intensity measurement range from 0 to 160000 Lux. Seeed Studio 114992868
No product available!
Module with an analog TEMT6000 light intensity sensor. The output voltage is linearly correlated with the intensity of the incident light. The module is supplied with the voltage from 3.3 to 5V
Module with digital light intensity sensor MAX44009. It is supplied with the voltage from 1.7 to 3.6 V and communicates via the I2C interface. GY-49
Module with ultraviolet (UV) sensor based on the GUVA-S12D system. It allows measurement of radiation with a wavelength in the range from 240 to 370 nm. The module has a connector in accordance with the Grove standard. Seeed Studio 101020043
SEN-14347