TSL25911FN light sensor module that can measure both visible and infrared light. It is an improved version of the TSL2561, offering a wider measurement range. The sensor has a built-in analog-to-digital converter (ADC), and the measurement result is available as light intensity and sent via an I2C interface. Thanks to this solution, signal noise is minimized. The sensor's sensitivity is as high as 188 uLux, and the dynamic range reaches 600M:1. The sensor also has a built-in infrared-responsive photodiode, making it possible to make precise measurements in strong infrared noise environments. An additional feature is the ability to program upper and lower thresholds, allowing the use of an interrupt function.
The sensor is compatible with 3.3V/5V operating voltages thanks to a built-in voltage level converter. Programming materials and instructions are provided with the module, including examples for popular platforms such as Raspberry Pi, Arduino and STM32. Full documentation is available on the manufacturer's website.
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Arduino Uno Rev3 is a popular board with Atmel ATmega328 microcontroller from the AVR family, there are 14 I / O lines, 6 PWM channels and 6 analog inputs. The additional ATmega16U4 microcontroller realizes communication via the USB interface. Arduino A000066
STM32 Nucleo-64 development board with STM32L476RGT6 MCU, supports Arduino and ST morpho connectivity
NUCLEO series starter kit equipped with STM32G474RE microcontroller (512 kB Flash, Cortex-M4), with built-in programmer-debugger ST-Link-V3E, equipped with connectors compatible with Arduino.
The long-awaited Raspberry Pi 4 model B with the SoC Broadcom BCM2711 (4 x Cortex-A72) running at 1.8 GHz, 3 GB LPDDR4 RAM and the Broadcom VideoCore VI graphics chip
The module allows measuring the light around the sensor. The measuring range is in the range 1 - 65535 LUX, and communication takes place using the I2C bus. modBH1750 (GY-302)
No product available!
SEN0162 This UV Sensor with GUVA-S12SD chip is suitable for detecting the UV raditation in sunlight. It can be used in UV Index Monitoring, DIY project, UV-A Lamp Monitoring, Plants growing Environmental monitoring...etc.
KAmodVL6180X is a module that allows to measure light intensity (ALS), distance to the object and recognition of gesture. It has an embedded voltage regulator and voltage level translators on signal lines. Thanks to this can be used in systems with 2.8...5.5V power supply voltage.
Color Sensor, complete color detector
Great way to upgrade a project that uses a photocell and needs RoHS compliance. Due to the high rejection ratio of infrared radiation, the spectral response of the ambient light sensor is close to that of human eyes. Adafruit 2748
TCS34725 RGB Color Sensor is a color sensor TCS34725 controlled by the I2C interface. It is powered by voltage in the range of 3.3 ... 5V and is intended for Arduino-compatible boards. DFRobot SEN0212
Module with ultraviolet (UV) sensor based on the GUVA-S12D system. It allows measurement of radiation with a wavelength in the range from 240 to 370 nm. The module has a connector in accordance with the Grove standard. Seeed Studio 101020043
Module with a flame sensor or other light sources with a wavelength in the range of 760 to 1100 nm. It was based on the YG1006 sensor (photovolver NPN). The sensor has a connector compatible with the Grove standard. Seeed studio 101020049
Module with digital light sensor TSL2561. The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 101020030
UV Sensor with response spectrum: 200nm-370nm
Gravity: I2C VEML7700 Ambient Light. Sensor SKU. SEN0228
A multifunctional module with an optical sensor for measuring the intensity of illumination, the color of the incident RGB light, the distance from the object and the detection of 3D gestures. Adafruit 3595
No product available!
No product available!
DFRobot Gravity analog light intensity module for Arduino and Raspberry Pi. DFRobot DFR0026
Sensor for detecting the distance, intensity and frequency of light (lightning) within a radius of 40 km. The module enables weather enthusiasts to measure data about local storms. DFRobot SEN0290
TSL25911FN light sensor module that can measure both visible and infrared light. It communicates via an I2C interface. Waveshare TSL25911 Light Sensor