The 315MHz RF receiver module is widely used in the field of vehicle Telecontrol, access control system, identification, etc. Compared with traditional wired communication, RF radio has advantage of higher flexibility and lower maintenance cost.
DFRobot 315MHz RF receiver module using SC2272-L4 low power decoder chip, with 8-bit three-state address coding switch, each one has three states: high level, low level, floating empty, so it supports up to 6,561 of the coding address. Modules can be used with SC2260, SC2262, PT2260, PT2262 and other coding chips, recommend our Remote Wireless Keyfob (315MHz)
Gravity: 315MHZ RF Receiver Module x1
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Expansion board for Arduino, allows easy connection of XBee modules, has separate outputs for I2C, SPI and UART buses. The built-in 3.3V voltage stabilizer and operating mode switch make it easier to program the Arduino when the XBee module is connected to the sockets. DFRobot DFR0265
Gravity: IO Expansion & Motor Driver Shield is an Arduino compatible expansion board that provides digital I / O ports, analog I2C, SPI and UART interfaces, as well as a DC motor driver. DFRobot DFR0502
Radio module with RFM69HCW 433 MHz chip, designed to work with the Raspberry Pi. Equipped with an OLED display and buttons. Adafruit 4073
Expansion board for STM32 Nucleo based on S2-LP RF transmitter operating in 868MHz band. The expansion board is compatible with ST morpho and Arduino UNO R3 connectors. STMicroelectronics X-NUCLEO-S2868A2
Module with 2.4 GHz transceiver system (transmitter and receiver) LT892. It is powered with the voltage of 3.3 V and has a built-in antenna
No product available!
Multi-channel wireless data transmission module operating at 433 MHz. It is supplied with the voltage ranging from 3.2 V to 5.5 V and communicates via the UART interface
A set with a radio transmitter and receiver operating at 433 MHz. The modules are equipped with Grove connectors and communicate via a digital interface. Seeed Studio 104020002
A set with a radio transmitter and receiver operating at 315 MHz. The modules are equipped with Grove connectors and communicate via a digital interface. Seeed Studio 113020001
6-channel transmitter (RC apparatus) 2.4 GHz Flysky FS-i6 with LCD display in set with receiver FS-IA6 with telemetry support. 6V power supply (4 x AA battery). Left-hand throttle (right-handed version). Flysky FS-i6
No product available!
Wireless communication module based on the NRF24L01 chip. It is designed for SMD mounting and will be perfect for the construction of small devices
No product available!
Module with a 433 MHz radio receiver for M5Stack sets. Based on the SYN531R chip, it has a built-in PCB antenna. M5Stack U113
A module with a 433 MHz radio transmitter for the M5Stack sets. Based on the SYN115 chip, it has a built-in PCB antenna. M5Stack U114
No product available!
Adapter with 3.3V voltage regulator designed for NRF24L01 modules with 8-pin connector
Wireless data transmission module operating at 433 MHz. It is powered with the voltage of 12 V
A set with a radio transmitter and receiver operating at 433 MHz. The modules are equipped with Gravity connectors and communicate via a digital interface. DFRobot TEL0140-1
Radio transmitter module operating at 433 MHz. It is equipped with Gravity connectors and communicates via a digital interface. DFRobot TEL0140
Radio receiver module operating at 433 MHz. It is equipped with Gravity connectors and communicates via a digital interface. DFRobot TEL0142
Wireless switch operating at 433 MHz frequency. It does not require a power supply. DFRobot TEL0146
DFRobot 315MHz RF receiver module using SC2272-L4 low power decoder chip. DFRobot TEL0112