Gravity: Analog EMG Sensor
ID: 569863
5902186313293
zł232.78
Tax included
zł189.25 tax excl.
A module with an EMG sensor that detects the activity of human muscles and neurons. Generates an analog signal in the range from 0 to 3 V on the output, it does not require the use of a conductive gel. DFRobot SEN0240
Description
A module with an EMG sensor that detects the activity of human muscles and neurons. The sensor connects the filtering and boosting circuit. By using a differential input and an analog filter circuit, noise, especially power frequency interference, is reduced. The output module generates an analog signal ranging from 0 to 3 V, and the waveform of the output signal indicates muscle activity. The activity of muscles and neurons is picked up by an electrode which allows to obtain a good quality signal without the need to use a conductive gel. The product Wiki page offers a user manual as well as sample programs and generated graphs.
Features
Signal transmitter module
- Detection range: +/- 1.5 mV
- Electrode connector: PJ-342
- Module connector: PH2.0-3P
- Working voltage: 3V
- Output voltage: 0 to 3V
- Supply voltage: 3.3 V to 5.5 V
- Working temperature: 0 to 50 ℃
- Size: 22 x 35 mm
Electrode board
- Electrode connector: PJ-342
- Cable length: 50 cm
- Plate size: 22 x 35 mm
- Weight: 36 g
Kit contains
- EMG electrode board
- Wrist strap
- Electrode cable
- EMG signal transmitter module
- 3-pin Gravity analog cable
569863
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
Arduino Uno Rev3 is a popular board with Atmel ATmega328 microcontroller from the AVR family, there are 14 I / O lines, 6 PWM channels and 6 analog inputs. The additional ATmega16U4 microcontroller realizes communication via the USB interface. Arduino A000066
zł108.57
24h
Available quantity: 145
Available
Available
Board with ATmega1280 microcontroller from the AVR family, the user has 54 I/O lines, 14 PWM channels, 16 analog inputs. DFRobot DFR0003
zł89.20
Delivery date unknown
No product available!
Other products in the same category (16)
Disposable biomedical electrodes that allow you to perform experimental ECG measurements. DFRobot FIT0510
zł19.84
24h
Available quantity: 2
Available
The module with the MAX30100 chip that monitors the oxygen content in the blood and the heart rate. It consists of two LED diodes, a photodetector, optimized optics and low noise analog signal processing. modMAX30100
zł14.37
24h
Available quantity: 3
Available
Module with a pulse sensor (heart rate). The board is equipped with a Grove connector and a digital output in the form of pulses. Seeed Studio 101020033
zł72.41
4 weeks
No product available!
A module with an EMG sensor that detects the activity of human muscles and neurons. Generates an analog signal in the range from 0 to 3 V on the output, it does not require the use of a conductive gel. DFRobot SEN0240
zł232.78
24h
Available quantity: 2
Available
Module with pulse and SpO2 level sensor (oxygen saturation level). The module is based on the MAX30102 chip and communicates via the I2C interface.
zł9.83
4 weeks
No product available!
Heart rate monitor module based on the MAX30102 chip. Powered with the voltage from 3.3 to 5V, communication via the I2C interface.
zł9.83
4 weeks
No product available!
Heart rate monitor module based on the popular MAX30101 and MAX32664. The board is equipped with connectors compliant with the Qwiic standard. SparkFun SEN-15219
zł227.53
24h
Available quantity: 3
Available
Module with GSR skin resistance sensor. It is used to measure skin activity, which reflects the stress response and experienced emotions. The board is equipped with a Grove connector and communicates via an analog interface. Seeed Studio 101020052
zł46.84
24h
Available quantity: 1
Available
Module with an EMG signal detector. The board is equipped with a Grove connector and has an analog output. Seeed Studio 101020058
zł146.37
24h
Available quantity: 1
Available
Module with heart rate and SpO2 sensor (oxygen saturation level) MAX30100 designed for M5Stack sets. M5Stack U029
zł54.00
24h
Available quantity: 3
Available
Module with a pulse sensor (heart rate). The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 103020024
zł139.17
24h
Available quantity: 1
Available
Module with a pulse sensor and SpO2 level (oxygen saturation level). It is based on the MAX30102 chip and MCU with heart rate and oximetry algorithm. Sensor communicates via the I2C interface. DFRobot SEN0344
zł69.90
24h
Available quantity: 1
Available
The module with a heart rate sensor and the SpO2 level dedicated to micro:bit. It is based on the MAX30102 chip and communicates via the I2C interface. SparkFun SEN-15271
zł73.84
24h
Available quantity: 1
Available
Module with heart rate sensor, SpO2 (oxygen saturation) and smoke levels. It is based on the MAX30101 chip and communicates via the I2C interface. Pimoroni PIM438
zł121.56
24h
Available quantity: 1
Available
Module with a pulse sensor and the level of SpO2 (oxygen saturation level). It is based on the MAX30102 chip, dedicated to the T-Wristband
zł38.08
4 weeks
No product available!
Module with a pulse sensor and the level of SpO2 (oxygen saturation level). It is based on the MAX30102 chip and communicates via the I2C or UART interface (Gravity connector). DFRobot SEN0518
zł111.32
24h
Available quantity: 1
Available
A module with an EMG sensor that detects the activity of human muscles and neurons. Generates an analog signal in the range from 0 to 3 V on the output, it does not require the use of a conductive gel. DFRobot SEN0240