![GY- MAX30102 - Heart rate sensor module and SpO2 GY- MAX30102 - Heart rate sensor module and SpO2](https://kamami.pl/35988-large_default/gy-max30102-heart-rate-sensor-module-and-spo2.jpg)
![GY- MAX30102 - Heart rate sensor module and SpO2 GY- MAX30102 - Heart rate sensor module and SpO2](https://kamami.pl/35988-large_default/gy-max30102-heart-rate-sensor-module-and-spo2.jpg)
zł8.03 tax excl.
Module with pulse and SpO2 level sensor (oxygen saturation level). The module is based on the MAX30102 chip and communicates via the I2C interface.
free shipping in Poland for all orders over 500 PLN
If your payment will be credited to our account by 11:00
Each consumer can return the purchased goods within 14 days
A small module with a heart rate sensor and SpO2 level (oxygen saturation level). The module is based on the MAX30102 chip and communicates via the I2C interface. It also has an interrupt output. The system contains internal LEDs, photodetectors and optical elements. MAX30102 is a complete system solution that facilitates the design process of mobile devices and wearable devices.
The module with the MAX30100 chip that monitors the oxygen content in the blood and the heart rate. It consists of two LED diodes, a photodetector, optimized optics and low noise analog signal processing. modMAX30100
Module with a pulse sensor and the level of SpO2 (oxygen saturation level). It is based on the MAX30102 chip, dedicated to the T-Wristband
Heart rate measurement module compatible with Arduino and Raspberry Pi (Gravity: Heart Rate Monitor Sensor For Arduino). It uses PPG technique, which in a simple and cheap way is able to measure the changing volume of blood. DFRobot SEN0203
The module with the MAX30100 chip that monitors the oxygen content in the blood and the heart rate. It consists of two LED diodes, a photodetector, optimized optics and low noise analog signal processing. modMAX30100
Module with a pulse sensor (heart rate). The board is equipped with a Grove connector and a digital output in the form of pulses. Seeed Studio 101020033
No product available!
A module with a sensor used to measure the activity of the heart. It allows you to strengthen and extract the heartbeat signals from biomedical electrodes. It has an analogue output and a heartbeat indicator (LED). SparkFun SEN-12650
Module with a pulse sensor and SpO2 level (oxygen saturation level). It is based on the MAX30102 chip and MCU with heart rate and oximetry algorithm. Sensor communicates via the I2C interface. DFRobot SEN0344
Sensor module for electromyography (EMG). Allows muscle activity to be studied and used to control devices. SparkFun DEV-21265
No product available!
Module with heart rate and SpO2 sensor (oxygen saturation level) MAX30100 designed for M5Stack sets. M5Stack U029
A module with an EMG sensor that detects the activity of human muscles and neurons. Generates an analog signal in the range from 0 to 3 V on the output, it does not require the use of a conductive gel. DFRobot SEN0240
No product available!
Module with an EMG signal detector. The board is equipped with a Grove connector and has an analog output. Seeed Studio 101020058
Evaluation board with built-in AD8232 heart monitor module and components placed in a way allowing effective implementation of medical and fitness applications, configuration of 2 or 3 electrodes
No product available!
Module with a pulse sensor (heart rate). The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 103020024
Disposable biomedical electrodes that allow you to perform experimental ECG measurements. DFRobot FIT0510
The MyoWare Power Shield is designed to take two standard CR2032 coin cell batteries to power the MyoWare Muscle Sensor. We have made this board in a way that the coin cell batteries are connected in parallel for extended capacity at a nominal 3.0V. DEV-13684
Module with GSR skin resistance sensor. It is used to measure skin activity, which reflects the stress response and experienced emotions. The board is equipped with a Grove connector and communicates via an analog interface. Seeed Studio 101020052
Module with pulse and SpO2 level sensor (oxygen saturation level). The module is based on the MAX30102 chip and communicates via the I2C interface.