zł90.50 tax excl.
Module with a pulse sensor and the level of SpO2 (oxygen saturation level). It is based on the MAX30102 chip and communicates via the I2C or UART interface (Gravity connector). DFRobot SEN0518
A small module with a pulse sensor and SpO2 level (oxygen saturation level). It is based on the MAX30102 chip and communicates via the I2C or UART interface (Gravity connector). The sensor consists of two LEDs, a photo detector, optimized optics and an analog signal processing circuit. MAX30102 provides a complete system solution to simplify the design process of mobile and wearable devices. The product wiki page offers complete documentation with examples of use.
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Arduino Uno Rev3 is a popular board with Atmel ATmega328 microcontroller from the AVR family, there are 14 I / O lines, 6 PWM channels and 6 analog inputs. The additional ATmega16U4 microcontroller realizes communication via the USB interface. Arduino A000066
Expansion board for Arduino, allows easy connection of XBee modules, has separate outputs for I2C, SPI and UART buses. The built-in 3.3V voltage stabilizer and operating mode switch make it easier to program the Arduino when the XBee module is connected to the sockets. DFRobot DFR0265
The expansion board is designed for DFRduino M0 or Bluno M0 sets. The board has 31 GPIO pins (including 6 PWM and 6 ADC inputs), UART, I2C and SPI interfaces. The pins are color coded according to the Gravity standard. DFRobot DFR0412
The expansion module for the Pyboard 1.1 set. The board has connectors compatible with the Gravity standard. Equipped with digital and analog pins, UART and I2C port. DFRobot DFR0577
No product available!
A set of 10 cables, 30 cm long, compliant with the Gravity standard. DFRobot FIT0513
Muscle Sensor Surface EMG Electrodes allow you to control your projects with your muscles. Adafruit 2773
No product available!
Module with a pulse sensor and the level of SpO2 (oxygen saturation level). It is based on the MAX30102 chip, dedicated to the T-Wristband
No product available!
Module with an EMG signal detector. The board is equipped with a Grove connector and has an analog output. Seeed Studio 101020058
The sensor responds to chakra changes in the tissues by analyzing the reflected light (the module contains an illuminator and a sensor).
Heart rate measurement module compatible with Arduino and Raspberry Pi (Gravity: Heart Rate Monitor Sensor For Arduino). It uses PPG technique, which in a simple and cheap way is able to measure the changing volume of blood. DFRobot SEN0203
Heart rate monitor module based on the popular MAX30101 and MAX32664. The board is equipped with connectors compliant with the Qwiic standard. SparkFun SEN-15219
No product available!
Evaluation board with built-in AD8232 heart monitor module and components placed in a way allowing effective implementation of medical and fitness applications, configuration of 2 or 3 electrodes
No product available!
A module with an EMG sensor that detects the activity of human muscles and neurons. Generates an analog signal in the range from 0 to 3 V on the output, it does not require the use of a conductive gel. DFRobot SEN0240
Module with heart rate sensor, SpO2 (oxygen saturation) and smoke levels. It is based on the MAX30101 chip and communicates via the I2C interface. Pimoroni PIM438
Module with a pulse sensor (heart rate). The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 103020024
Designed to pair with the MyoWare Muscle Sensor; 10-segment bar graph shows the magnitude of the measured signal. The more muscle activation measured, the higher up the board the lit LEDs will go. DEV-13688
Heart rate monitor module based on the MAX30102 chip. Powered with the voltage from 3.3 to 5V, communication via the I2C interface.
Disposable biomedical electrodes that allow you to perform experimental ECG measurements. DFRobot FIT0510
Iduino SE049 is a simple and functional heart rate sensor, ideal for educational and hobbyist projects in the fields of electronics and bioengineering. Thanks to its compatibility with Arduino and intuitive operation, it allows for the creation of custom measurement devices such as pulse meters or smart health-monitoring wristbands. It is suitable for mobile and stationary applications as part of a diagnostic or training system.
The module with the MAX30100 chip that monitors the oxygen content in the blood and the heart rate. It consists of two LED diodes, a photodetector, optimized optics and low noise analog signal processing. modMAX30100
Module with a pulse sensor and the level of SpO2 (oxygen saturation level). It is based on the MAX30102 chip and communicates via the I2C or UART interface (Gravity connector). DFRobot SEN0518