 
        
           
        
          Heart rate monitor module based on the popular MAX30102 chip. MAX30102 is a pulse oximetry and pulse measurement module, designed for the high demands of wearable devices. The circuit consists of two LEDs, a photo detector, optimized optics and an analog signal processing circuit. The module allows you to measure the level of blood saturation with oxygen and measure temperature. The module communicates with the supervisory system via the I2C interface.
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Cables for evaluation boards, set of 10 pcs., blue colour
Cables for evaluation boards, set of 10 pcs., red colour
Cables for evaluation boards, set of 10 pcs., green colour
Cables for evaluation boards, set of 10 pcs., yellow colour
A set of 10 female-female connection cables, in various colors, 17 cm long. CAB_F-F (Rainbow-10-17)
Module with pulse and SpO2 level sensor (oxygen saturation level). The module is based on the MAX30102 chip and communicates via the I2C interface.
Module with a pulse sensor and SpO2 level (oxygen saturation level). It is based on the MAX30102 chip and MCU with heart rate and oximetry algorithm. Sensor communicates via the I2C interface. DFRobot SEN0344
Designed to pair with the MyoWare Muscle Sensor; 10-segment bar graph shows the magnitude of the measured signal. The more muscle activation measured, the higher up the board the lit LEDs will go. DEV-13688
Module with heart rate sensor, SpO2 (oxygen saturation) and smoke levels. It is based on the MAX30101 chip and communicates via the I2C interface. Pimoroni PIM438
Module with a pulse sensor (heart rate). The board is equipped with a Grove connector and a digital output in the form of pulses. Seeed Studio 101020033
 No product available!
Gravity: Heart Rate Monitor Sensor is a sensor used to measure heart activity. Adapted for easy use with Arduino. SparkFun SEN0213
Disposable biomedical electrodes that allow you to perform experimental ECG measurements. DFRobot FIT0510
The module with the MAX30100 chip that monitors the oxygen content in the blood and the heart rate. It consists of two LED diodes, a photodetector, optimized optics and low noise analog signal processing. modMAX30100
A module with an EMG sensor that detects the activity of human muscles and neurons. Generates an analog signal in the range from 0 to 3 V on the output, it does not require the use of a conductive gel. DFRobot SEN0240
Module with heart rate and SpO2 sensor (oxygen saturation level) MAX30100 designed for M5Stack sets. M5Stack U029
Heart rate monitor module based on the popular MAX30101 and MAX32664. The board is equipped with connectors compliant with the Qwiic standard. SparkFun SEN-15219
 No product available!
Muscle Sensor Surface EMG Electrodes allow you to control your projects with your muscles. Adafruit 2773
 No product available!
The sensor responds to chakra changes in the tissues by analyzing the reflected light (the module contains an illuminator and a sensor).
The module with a heart rate sensor and the SpO2 level dedicated to micro:bit. It is based on the MAX30102 chip and communicates via the I2C interface. SparkFun SEN-15271
A module with a sensor used to measure the activity of the heart. It allows you to strengthen and extract the heartbeat signals from biomedical electrodes. It has an analogue output and a heartbeat indicator (LED). SparkFun SEN-12650
 
                    Heart rate monitor module based on the MAX30102 chip. Powered with the voltage from 3.3 to 5V, communication via the I2C interface.