![Module for measuring heart rate and oxygen content in the blood](https://kamami.pl/75926-large_default/module-for-measuring-heart-rate-and-oxygen-content-in-the-blood.jpg)
![Module for measuring heart rate and oxygen content in the blood](https://kamami.pl/75926-large_default/module-for-measuring-heart-rate-and-oxygen-content-in-the-blood.jpg)
zł12.11 tax excl.
The module with the MAX30100 chip that monitors the oxygen content in the blood and the heart rate. It consists of two LED diodes, a photodetector, optimized optics and low noise analog signal processing. modMAX30100
free shipping in Poland for all orders over 500 PLN
If your payment will be credited to our account by 11:00
Each consumer can return the purchased goods within 14 days
The module with the MAX30100 chip that monitors the oxygen content in the blood and the heart rate. It consists of two LED diodes, a photodetector, optimized optics and low noise analog signal processing.
Evaluation board with built-in AD8232 heart monitor module and components placed in a way allowing effective implementation of medical and fitness applications, configuration of 2 or 3 electrodes
No product available!
Heart rate measurement module compatible with Arduino and Raspberry Pi (Gravity: Heart Rate Monitor Sensor For Arduino). It uses PPG technique, which in a simple and cheap way is able to measure the changing volume of blood. DFRobot SEN0203
A module with an EMG sensor that detects the activity of human muscles and neurons. Generates an analog signal in the range from 0 to 3 V on the output, it does not require the use of a conductive gel. DFRobot SEN0240
Module with a pulse sensor and the level of SpO2 (oxygen saturation level). It is based on the MAX30102 chip, dedicated to the T-Wristband
Disposable biomedical electrodes that allow you to perform experimental ECG measurements. DFRobot FIT0510
Module with heart rate and SpO2 sensor (oxygen saturation level) MAX30100 designed for M5Stack sets. M5Stack U029
Designed to pair with the MyoWare Muscle Sensor; 10-segment bar graph shows the magnitude of the measured signal. The more muscle activation measured, the higher up the board the lit LEDs will go. DEV-13688
Module with a pulse sensor and SpO2 level (oxygen saturation level). It is based on the MAX30102 chip and MCU with heart rate and oximetry algorithm. Sensor communicates via the I2C interface. DFRobot SEN0344
The MyoWare Power Shield is designed to take two standard CR2032 coin cell batteries to power the MyoWare Muscle Sensor. We have made this board in a way that the coin cell batteries are connected in parallel for extended capacity at a nominal 3.0V. DEV-13684
The module with a heart rate sensor and the SpO2 level dedicated to micro:bit. It is based on the MAX30102 chip and communicates via the I2C interface. SparkFun SEN-15271
Module with a pulse sensor (heart rate). The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 103020024
Muscle Sensor Surface EMG Electrodes allow you to control your projects with your muscles. Adafruit 2773
No product available!
Module with a pulse sensor and the level of SpO2 (oxygen saturation level). It is based on the MAX30102 chip and communicates via the I2C or UART interface (Gravity connector). DFRobot SEN0518
Module with GSR skin resistance sensor. It is used to measure skin activity, which reflects the stress response and experienced emotions. The board is equipped with a Grove connector and communicates via an analog interface. Seeed Studio 101020052
Gravity: Heart Rate Monitor Sensor is a sensor used to measure heart activity. Adapted for easy use with Arduino. SparkFun SEN0213
Module with an EMG signal detector. The board is equipped with a Grove connector and has an analog output. Seeed Studio 101020058
Heart rate measurement module compatible with Arduino and Raspberry Pi (Gravity: Heart Rate Monitor Sensor For Arduino). It uses PPG technique, which in a simple and cheap way is able to measure the changing volume of blood. DFRobot SEN0203
Module with heart rate sensor, SpO2 (oxygen saturation) and smoke levels. It is based on the MAX30101 chip and communicates via the I2C interface. Pimoroni PIM438
The module with the MAX30100 chip that monitors the oxygen content in the blood and the heart rate. It consists of two LED diodes, a photodetector, optimized optics and low noise analog signal processing. modMAX30100