MLX90640 IR Thermal Camera - module with MLX90640 thermal imaging camera (FoV 110°)
ID: 587272
5906623430444
zł487.45
Tax included
zł396.30 tax excl.
Module with MLX90640 thermal imaging camera with a matrix of 32x24 fields and a viewing angle of 110°. The board is equipped with a STEMMA QT connector and communicates via the I2C interface. Adafruit 4469
Description
Module with MLX90640 thermal imaging camera with a matrix of 32x24 fields and a viewing angle of 110°. It enables temperature measurement in the range from -40°C to 300°C with high accuracy up to 1.5°C. The infrared thermal imaging camera is equipped with a sensitive heat sensor that can detect slight differences in the temperature of objects in the environment. It then collects radiation information from the objects and creates an electronic image (32x24 field matrix). The board is equipped with a STEMMA QT connector and communicates via the I2C interface. It is supplied with the voltage from 3.3 V to 5 V. Full documentation of the module with examples of use is available on the product page.
Attention!
To operate the module, a chip with at least 20 KB of RAM is required.Features
- Sensor: MLX90640
- Resolution: 32x24
- FoV: 110°x70°
- Temperature measurement range: -40 ? to 300 ?
- Refresh rate: 0.5Hz to 64Hz
- I2C interface
- I2C address: 0x33
- Supply voltage: 3.3 to 5 V
- Current consumption: 18 mA
- Dimensions: 25.7 x 17.7 x 16 mm
Kit contains
- MLX90640 IR Thermal Camera
- Straight 5-pin male goldpin connector
587272
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
The long-awaited Raspberry Pi 4 model B with the SoC Broadcom BCM2711 SoC (4 x Cortex-A72) running at 1.8 GHz, 4 GB LPDDR4 RAM and the Broadcom VideoCore VI graphics chip
zł338.00
Delivery date unknown
No product available!
Flexible Qwiic cable 150 mm long. On one side it is terminated with a female Qwiic connector, and on the other side with single male goldpin connectors. SparkFun PRT-17912
zł10.47
24h
Available quantity: 3
Available
Flexible 4-core cable, 200 mm long, terminated on both sides with a Qwiic plug. Sparkfun PRT-17258
zł12.96
Delivery date unknown
No product available!
Other products in the same category (16)
Module with 8-bit ADC and 8-bit DAC. It allows you to measure voltage and generate an analog signal. Communicates via I2C. Adafruit 4648
zł33.59
24h
Available quantity: 2
Available
Module with a digital temperature sensor PCT2075. It enables measurement in the range from -25 to 100°C with an accuracy of ±1°C. Communicates via I2C. Adafruit 4369
zł34.08
24h
Available quantity: 3
Available
Module with a 10-channel AS7341 sensor that detects light in various wavelength ranges (color detection). It communicates via the I2C interface. Adafruit 4698
zł94.62
24h
Available quantity: 4
Available
Module with TLV493D 3-axis magnetic field sensor. Equipped with a STEMMA QT connector, it communicates via the I2C interface. Adafruit 4366
zł33.69
24h
Available quantity: 2
Available
I2C bus amplifier module based on the LTC4311 system. It enables communication via a popular interface over much longer distances while maintaining high transmission speeds. Adafruit 4756
zł35.87
24h
Available quantity: 6
Available
Module with MLX90640 thermal imaging camera with a matrix of 32x24 fields and a viewing angle of 110°. The board is equipped with a STEMMA QT connector and communicates via the I2C interface. Adafruit 4469
zł487.45
24h
Available quantity: 1
Available
Module with a GPS receiver based on the MTK3333 chip. It is equipped with a STEMMA QT connector and communicates via the UART or I2C interface. Adafruit 4415
zł180.63
24h
Available quantity: 3
Available
A module with a fan controller and a temperature sensor based on the EMC2101 system. Equipped with a STEMMA QT connector, it communicates via the I2C interface. Adafruit 4808
zł28.84
24h
Available quantity: 1
Available
Module with digital barometer BMP388. It measures pressure in the range from 300 to 1250 hPa and communicates via I2C or SPI. Adafruit 3966
zł49.78
24h
Available quantity: 3
Available
Air quality sensor module PMSA003I. It allows for a precise analysis of the amount of pollutants in the environment based on the concentration of PM1.0, PM2.5 and PM10 particles. Adafruit 4632
zł228.94
24h
Available quantity: 1
Available
Module with a digital barometer DPS310. It enables pressure measurement in the range from 300 to 1200 hPa and communicates via I2C or SPI. Adafruit 4494
zł35.79
24h
Available quantity: 1
Available
Module with acceleration and rotational speed sensor based on the MPU-6050 system. Equipped with a STEMMA QT connector, it communicates via the I2C interface. Adafruit 3886
zł72.23
4 weeks
No product available!
The expansion module is designed to work with the Raspberry Pi 400. The board has a 40-pin connector placed in a vertical position and a connector for RPI 400 at an angle of 45°. Adafruit 4862
zł40.98
24h
Available quantity: 2
Available
Module with a temperature and humidity sensor based on the HTU31 system. Equipped with a STEMMA QT connector, it communicates via the I2C interface. Adafruit 4832
zł39.52
24h
Available quantity: 3
Available
The module with a black and white OLED display with a diagonal of 0.91" and a resolution of 128x32 pixels. Equipped with a STEMMA QT connector, communicates via the I2C interface. Adafruit 4440
zł84.39
24h
Available quantity: 1
Available
Module with sensor TMP117. It enables measurement in the range from –55°C to 150°C with a very high accuracy up to ± 0.1°C. It communicates via the I2C interface. Adafruit 4821
zł60.21
4 weeks
No product available!
Module with MLX90640 thermal imaging camera with a matrix of 32x24 fields and a viewing angle of 110°. The board is equipped with a STEMMA QT connector and communicates via the I2C interface. Adafruit 4469