STEMMA QT ENS160 MOX Gas Sensor - module with a gas sensor
ID: 1181770
5906623433636
zł129.42
Tax included
zł105.22 tax excl.
Module with ENS160 gas sensor for measuring the concentration of carbon dioxide (eCO2) and volatile organic compounds (TVOC) in the air. It communicates via the I2C or SPI interface. Adafruit 5606
Description
Module with ENS160 gas sensor. It has been specially designed for indoor air quality monitoring and offers the detection of multiple IAQ parameters (TVOC, eCO2, AQI). The innovative TrueVOC ™ technology provides the sensor with the highest accuracy, fast response and protection against interference. It can be widely used in many areas such as air quality detection, air purifiers and ventilation systems. It can work with systems with a working voltage of 3.3 V or 5 V, and communication is via the I2C interface (STEMMA QT connector) or SPI. Full documentation with examples is available on the product page.
Features
- Support for up to 4 independent MOX gas sensors
- ECO2 measuring range: 400 to 65,000 ppm
- TVOC measurement range: 0 to 65,000 ppb
- Fully calibrated
- I2C digital interface (address 0x52 or 0x53) or SPI
- Power supply: 3.3 V to 5 V
- Module dimensions: 25.4 x 17.6 x 4.5 mm
Kit contains
- STEMMA QT ENS160 MOX Gas Sensor
- 8-pin straight male goldpin connector
1181770
Data sheet
- Interface
- SPI/I2C
- Type of sensor
- ENS160
- Power supply voltage
- 3,3 - 5 V
- Concentration measurement
- VOC/CO2
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
The board with the RP2040 microcontroller equipped with two ARM Cortex-M0+ cores, which work at a frequency of 133 MHz, 264 kB RAM. The board also has 8 MB of QSPI flash memory. The circuit can be programmed in C/C++, CircuitPython or MicroPython. Adafruit 4900
zł51.49
Delivery date unknown
No product available!
Board with the WiFi Espressif ESP32-S2 module. It offers 4 MB of Flash memory and 2 MB of SRAM and an RGB LED. It is equipped with a STEMMA QT connector. Adafruit 5325
zł74.27
24h
Available quantity: 3
Available
4-wire cable with a length of 50 mm. Both ends with STEMMA QT (Qwiic) plug. Adafruit 4399
zł5.98
24h
Available quantity: 34
Available
4-wire cable with a length of 100 mm. Both ends with STEMMA QT (Qwiic) plug. Adafruit 4210
zł5.29
24h
Available quantity: 1
Available
4-core cable with a length of 200 mm. Both ends with STEMMA QT (Qwiic) plug. Adafruit 4401
zł7.69
24h
Available quantity: 10
Available
Other products in the same category (16)
Module with an analog MQ8 hydrogen sensor. It is powered with the voltage of 5 V and has an analog output. DFRobot SEN0133
zł44.06
24h
Available quantity: 1
Available
Module with an analog MQ5 LPG sensor. It is powered with the voltage of 5 V and has an analog output. DFRobot SEN0130
zł29.50
24h
Available quantity: 1
Available
Module with an analog MQ6 propane sensor. It is powered with the voltage of 5 V and has an analog output. DFRobot SEN0131
zł32.83
24h
Available quantity: 1
Available
Module with an ozone detection sensor that performs measurements in the range of up to 10 ppm with a resolution of 0.01 ppm. The module is equipped with an I2C interface. DFRobot SEN0321
zł225.71
4 weeks
No product available!
Module with gas sensor SGP30. It allows you to measure the content of total volatile organic compounds (TVOC), carbon dioxide equivalent (eCO2), ethanol and H2 in the air. M5Stack U088
zł60.90
24h
Available quantity: 3
Available
Module with four gas sensors that allow the detection of CO, NO2, alcohol and volatile organic compounds (VOC). The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 101020820
zł158.82
24h
Available quantity: 1
Available
Module with a gas concentration sensor MQ9, which enables the detection of carbon monoxide and combustible gases (methane, propane). The board is equipped with a Grove connector and communicates via an analog interface. Seeed Studio 101020045
zł49.46
24h
Available quantity: 2
Available
Module with the alcohol sensor MQ303A. The board is equipped with a Grove connector and communicates via an analog interface. Seeed Studio 101020044
zł43.95
24h
Available quantity: 1
Available
Module with Sensirion SCD30 sensor, which enables CO2, temperature and humidity measurement. The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 101020634
zł298.42
4 weeks
No product available!
Module with a BME680 sensor that allows you to measure temperature, humidity, pressure and gas detection. The board is equipped with a Grove connector and communicates via I2C and SPI. Seeed Studio 101020513
zł110.07
4 weeks
No product available!
Module with air quality sensor SGP30. The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 101020512
zł49.16
24h
Available quantity: 3
Available
Module with the MQ3 alcohol concentration sensor. The board is equipped with a Grove connector and communicates via an analog interface. Seeed Studio 101020006
zł19.54
24h
Available quantity: 2
Available
Module with MQ5 LPG concentration sensor. The board is equipped with a Grove connector and communicates via an analog interface. Seeed Studio 101020056
zł55.95
24h
Available quantity: 2
Available
Module with a gas concentration sensor MQ2, which enables the detection of LPG, butane, propane, methane, alcohol, hydrogen and smoke. The board is equipped with a Grove connector and communicates via an analog interface. Seeed Studio 101020055
zł41.71
24h
Available quantity: 2
Available
Air quality sensor module based on the SGP40 system. It communicates via the I2C interface. DFRobot SEN0392
zł72.52
24h
Available quantity: 1
Available
Module with BME680 sensor for measuring the concentration of volatile organic compounds (VOC), pressure, temperature and humidity. I2C or SPI communication. DFRobot SEN0375
zł79.85
24h
Available quantity: 2
Available
Module with ENS160 gas sensor for measuring the concentration of carbon dioxide (eCO2) and volatile organic compounds (TVOC) in the air. It communicates via the I2C or SPI interface. Adafruit 5606