

In the case of working with a MCU:
Part Number | Sensitive Gas | Application |
---|---|---|
MQ-135 Gas Sensor | benzene, alcohol, smoke | Air quality monitor |
MQ-2 Gas Sensor | LPG, propane, hydrogen | Gas leakage detector |
MQ-3 Gas Sensor | alcohol, ethanol | Car alcohol alarm, breathalyser |
MQ-5 Gas Sensor | LPG, natural gas, coal gas | Gas leakage detector |
MQ-7 Gas Sensor | carbon monoxide | Carbon monoxide monitor |
Weight: 0.011 kg
Data sheet
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
The sensor is designed for indoor air quality testing. The main gas detected is carbon monoxide, alcohol, acetone, thinner, formaldehyde and other slightly toxic gases. It is compatible with 5V and 3.3V power supply. Seeed Studio 101020078
Digital gas sensor solution that senses a wide range of Total Volatile Organic Compounds (TVOCs), including equivalent carbon dioxide (eCO2) and metal oxide (MOX) levels, intended for indoor air quality monitoring in personal devices such as watches and phones, but we’ve put it on a breakout board so you can use it as a regular I2C device. SEN-14193
The module allows the detection of volatile organic compounds (VOC) in the air, based on Winsen\'s WSP2110 system. Allows for detection in the air; formaldehyde (HCHO), methane, benzene, toluene, alcohol, etc. The sensor output is an analog signal. Seeed studio 101020001
Module with SGP30 gas sensor. The sensor communicates via the I2C interface. SGP30 system contains several elements reacting to various metal oxides, which allows for more accurate determination of air quality. Adafruit 3709
Formaldehyde sensor (HCHO) dedicated to measuring ambient air quality. It is used to detect whether the surrounding environment exceeds a set concentration threshold. It is powered by a voltage of 5 V to 24 V and has an output in the form of a two-state digital signal. DFRobot SEN0595
The MQ-6 sensor allows the measurement of LPG, propane and isobutane. The measuring range of the sensor is in the range of 300 - 10.000 ppm, while the output receives an analog signal.
The MQ-3 sensor allows you to measure the concentration of alcohol vapors. The measuring range of the sensor is in the range of 0.05 mg / L to 10mg / L, and an analogue signal is obtained at the output.
The module with an alcohol sensor (MQ-3), allows you to measure the concentration of ethanol in the air. The module has an analogue output and an output triggered by exceeding the threshold of sensitivity.
The MQ-8 module allows the measurement of hydrogen concentration in the air. It has an analogue output and an output triggered by exceeding the threshold of sensitivity.
Sensor that detects the concentration of chlorine. Equipped with a factory calibrated probe. It communicates via the I2C interface, UART or analog output. DFRobot SEN0468
No product available!
A sensor that detects the concentration of hydrogen fluoride. Equipped with a factory calibrated probe. It communicates via the I2C interface, UART or analog output. DFRobot SEN0475
No product available!
The MQ-9 sensor allows the measurement of gas concentrations such as carbon monoxide, propane and methane. Sensor measuring range: 10 - 10,000 ppm
Module with BME680 sensor for measuring environmental conditions such as concentration of volatile organic compounds (VOC), atmospheric pressure, temperature and humidity. I2C or SPI communication. SparkFun SEN-16466
Module with the MQ3 alcohol concentration sensor. The board is equipped with a Grove connector and communicates via an analog interface. Seeed Studio 101020006
The MQ-8 sensor allows the measurement of hydrogen concentration in the air. The measuring range of the sensor is in the range of 100 - 10,000 ppm.
Module with Sensirion SCD30 sensor, which enables CO2, temperature and humidity measurement. The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 101020634
Air quality sensor module based on SGP30 system. The board has been equipped with Qwiic connectors. SparkFun SEN-16531
Module with a sensor of formaldehyde (methanal) concentration in the air. The board is equipped with a Grove connector and communicates via the I2C or UART interface. Seeed Studio 101020972
No product available!
Module with the MiCS-5524 analog gas sensor. It allows you to measure the concentration of CO, CH4, 2H5OH, C3H8, C4H10, H2, H2S and NH3. DFRobot SEN0440
Module with integrated BME688 gas, pressure, temperature and humidity sensor placed in one MEMS housing. It is equipped with an I2C interface. Adafruit 5046
MQ-135 Gas Sensor