

Module with CO2, temperature and humidity sensor SCD-30. It allows you to measure the concentration of carbon dioxide in the environment in the range from 400 to 10,000 ppm. In addition, the system has an integrated temperature and humidity sensor, which makes it suitable for detecting environmental parameters, scientific experiments and air quality tests. It can work with systems with a working voltage of 3.3 V or 5 V, and communication is via the I2C interface (STEMMA QT connector). Full documentation with examples is available on the product page.
Data sheet
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Module with SGP30 gas sensor. The sensor communicates via the I2C interface. SGP30 system contains several elements reacting to various metal oxides, which allows for more accurate determination of air quality. Adafruit 3709
PM2.5 dust sensor powered by 5V, communication via the UART interface. Sharp GP2Y1051AU0F
Flexible Qwiic cable, 150 mm long. On one side it is terminated with a female Qwiic connector, and on the other side with single female goldpin connectors. SparkFun PRT-17261
No product available!
Flexible 4-core cable, 100 mm long, terminated on both sides with a Qwiic plug. Sparkfun PRT-17259
Module with BME680 for measuring the concentration of VOC, pressure, temperature and humidity. Equipped with a STEMMA QT connector, it communicates via I2C or SPI. Adafruit 3660
Air quality sensor module based on the SGP40 system. It uses CMOSens technology by Sensirion and provides information on the concentration of volatile organic compounds (VOC). Adafruit 4829
ENS160 gas sensor module to measure the concentration of carbon dioxide (eCO2) and volatile organic compounds (TVOC) in the air. It communicates via an I2C or SPI interface. SparkFun SEN-20844
Module with ozone detection sensor. It performs measurements up to 10 ppm with a resolution of 0.01 ppm. It has a UART output and an analog output. ZE25-O3
Module with air quality sensor SGP30. It allows you to read the concentration of VOC (TVOC) and eCO2 and communicates via the I2C interface. Pimoroni PIM480
Module with Sensirion SCD30 sensor, which enables CO2, temperature and humidity measurement. The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 101020634
Module with BME680 for measuring the concentration of VOC, pressure, temperature and humidity. Equipped with a STEMMA QT connector, it communicates via I2C or SPI. Adafruit 3660
Formaldehyde sensor (HCHO) dedicated to measuring ambient air quality. It is used to detect whether the surrounding environment exceeds a set concentration threshold. It is powered by a voltage of 5 V to 24 V and has an output in the form of a two-state digital signal. DFRobot SEN0595
Module with an oxygen concentration sensor in the environment. It allows you to measure the volume of oxygen in the range from 0 to 100%. It communicates via the I2C interface. DFRobot SEN0496
No product available!
The MQ-2 sensor allows the measurement of gas concentrations such as propane, butane, methane, LPG as well as alcohol and smoke. Sensor measuring range: up to 10,000 ppm
The MQ-3 sensor allows you to measure the concentration of alcohol vapors. The measuring range of the sensor is in the range of 0.05 mg / L to 10mg / L, and an analogue signal is obtained at the output.
The module with a smoke sensor and flammable gases (MQ-2) allows the measurement of gas concentrations such as natural gas, hydrogen as well as smoke and ethanol. The module has an analogue output and an output triggered by exceeding the threshold of sensitivity. modMQ-2
The module allows the detection of volatile organic compounds (VOC) in the air, based on Winsen\'s WSP2110 system. Allows for detection in the air; formaldehyde (HCHO), methane, benzene, toluene, alcohol, etc. The sensor output is an analog signal. Seeed studio 101020001
Integrated gas sensor, pressure, humidity and temperature in the LGA-8 housing. Bosch Sensortec BME680
Module with the MQ3 analog alcohol sensor. It allows you to detect gas and build a simple breathalyzer. The module is powered by 5 V and has an analog output
Integrated BME688 gas, pressure, temperature and humidity sensor in one MEMS housing. The system can be supplied with the voltage of 3.3 V and is equipped with an I2C communication interface. BME688 Breakout Board
Module with CO2, temperature and humidity sensor SCD-30. Equipped with a STEMMA QT connector, it communicates via the I2C interface. Adafruit 4867