zł571.51 tax excl.
A sensor that detects the concentration of sulfur dioxide. Equipped with a factory calibrated probe. It communicates via the I2C interface, UART or analog output. DFRobot SEN0470
A sensor that detects the concentration of sulfur dioxide. It is equipped with a factory calibrated probe and allows you to quickly and accurately measure the concentration of gas in the environment. The probe used is resistant to interference, offers high stability and sensitivity as well as a service life of up to two years. The sensor communicates via the I2C interface, UART or analog output, has 32 modifiable I2C addresses, an integrated temperature compensation algorithm and a threshold alarm function. It can be widely used for the detection of sulfur dioxide in industry and environmental protection. Full documentation and examples of use are available on the product page.
Data sheet
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Arduino Uno Rev3 is a popular board with Atmel ATmega328 microcontroller from the AVR family, there are 14 I / O lines, 6 PWM channels and 6 analog inputs. The additional ATmega16U4 microcontroller realizes communication via the USB interface. Arduino A000066
Gravity: Formaldehyde (HCHO) Sensor is a module for measuring the concentration of formaldehyde (methane) in the air. It can be supplied with voltage in the range of 3.3 ... 6V. DFRobot SEN0231
A set of 10 cables, 30 cm long, compliant with the Gravity standard. DFRobot FIT0513
A sensor that detects the concentration of hydrogen fluoride. Equipped with a factory calibrated probe. It communicates via the I2C interface, UART or analog output. DFRobot SEN0475
No product available!
Module with CO2, temperature and humidity sensor SCD-40. Equipped with a STEMMA QT connector, it communicates via the I2C interface. Adafruit 5187
The MQ-9 sensor allows the measurement of gas concentrations such as carbon monoxide, propane and methane. Sensor measuring range: 10 - 10,000 ppm
Gravity: Formaldehyde (HCHO) Sensor is a module for measuring the concentration of formaldehyde (methane) in the air. It can be supplied with voltage in the range of 3.3 ... 6V. DFRobot SEN0231
The SCD-40 CO2, temperature and humidity sensor module provides high accuracy readings. It is equipped with a Qwiic connector and communicates via an I2C interface. SparkFun SEN-22395
Module with an analog MQ8 hydrogen sensor. It is powered with the voltage of 5 V and has an analog output. DFRobot SEN0133
Module with BME680 sensor for measuring environmental conditions such as concentration of volatile organic compounds (VOC), atmospheric pressure, temperature and humidity. I2C or SPI communication. SparkFun SEN-16466
The module allows the detection of volatile organic compounds (VOC) in the air, based on Winsen\'s WSP2110 system. Allows for detection in the air; formaldehyde (HCHO), methane, benzene, toluene, alcohol, etc. The sensor output is an analog signal. Seeed studio 101020001
A module for the detection of gases and vapors of alcohols, including ethanol.
Module with an ozone detection sensor that performs measurements in the range of up to 10 ppm with a resolution of 0.01 ppm. The module is equipped with an I2C interface. DFRobot SEN0321
No product available!
Air quality sensor module based on the SGP40 system. It communicates via the I2C interface. DFRobot SEN0392
Air quality sensor module based on SGP30 system. The board has been equipped with Qwiic connectors. SparkFun SEN-16531
Module with a smoke concentration sensor made in MEMS technology. It allows gas detection in the range of 10 to 1000 ppm and has an analog output. DFRobot SEN0570
Module with air quality sensor SGP30. The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 101020512
Air quality sensor module based on the ENS160 system. It communicates via the I2C or SPI interface. DFRobot SEN0515
Integrated gas sensor, pressure, humidity and temperature in the LGA-8 housing. Bosch Sensortec BME680
Module with a formaldehyde sensor made in MEMS technology. It allows gas detection in the range of 0 to 3 ppm and has an analog output. DFRobot SEN0563
A sensor that detects the concentration of sulfur dioxide. Equipped with a factory calibrated probe. It communicates via the I2C interface, UART or analog output. DFRobot SEN0470