Fermion: MEMS Carbon Monoxide CO Gas Detection Sensor - a module with a carbon monoxide sensor
ID: 1186658
5902186311213
zł26.78
Tax included
zł21.77 tax excl.
Carbon monoxide sensor module made in MEMS technology. It allows gas detection in the range of 5 to 5000 ppm and has an analog output. DFRobot SEN0564
Description
A module with a carbon monoxide sensor that uses the latest technology of the microelectromechanical system (MEMS), thanks to which the sensor has compact dimensions, low power consumption, short time of obtaining measurements and quick response. It can qualitatively measure the concentration of carbon monoxide in the range of 5 to 5000 ppm and is suitable for generating leak alarms, e.g. in portable gas detectors. The sensor has an analog output and is supplied with a voltage of 3.3 V to 5 V. Full documentation and sample programs are available on the product page.
Features
- Detected gas: CO
- Detection range: 5 to 5000 ppm
- Output signal: analog
- Sensitivity: R0 (in air)/Rs (at 150ppm CO) ≥ 3
- Working temperature: -10-50℃
- Operating humidity: 15-90% RH (non-condensing)
- Lifespan: ≥5 years (in the air)
- Power supply: 3.3 to 5V
- Operating Current: <20mA
- Dimension: 13×13×2.5mm
Kit contains
- Fermion: MEMS Carbon Monoxide CO Sensor
- Goldpin male connector
1186658
Data sheet
- Interface
- Sygnał analogowy
- Type of sensor
- inny
- Power supply voltage
- 3,3 V/5 V
- Concentration measurement
- CO
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
Gravity: I2C ADS1115 The 16-Bit ADC Module is an analogue-to-digital converter module for Arduino and Raspberry Pi. This module uses 16-bit ADC ADS1115 and is powered by 3.3 ... 5V. DFRobot DFR0553
zł77.42
24h
Available quantity: 4
Available
Other products in the same category (16)
Module with BME680 for measuring the concentration of VOC, pressure, temperature and humidity. Equipped with a STEMMA QT connector, it communicates via I2C or SPI. Adafruit 3660
zł105.20
24h
Available quantity: 1
Available
Module with four gas sensors that allow the detection of CO, NO2, alcohol and volatile organic compounds (VOC). The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 101020820
zł158.82
24h
Available quantity: 2
Available
A sensor that detects the concentration of hydrogen chloride. Equipped with a factory calibrated probe. It communicates via the I2C interface, UART or analog output. DFRobot SEN0474
zł925.55
4 weeks
No product available!
A sensor that detects the concentration of hydrogen sulphide. Equipped with a factory calibrated probe. It communicates via the I2C interface, UART or analog output. DFRobot SEN0467
zł335.61
4 weeks
No product available!
A sensor used to detect air pollutants by measuring VOCs and gases such as ammonia or hydrogen sulfide. It is used in various areas, such as the food industry, chemical industry, air quality control in laboratories and environmental monitoring. Figaro TGS2602
zł31.33
24h
Available quantity: 14
Available
Air quality sensor module based on the ENS160 system. It communicates via the I2C or SPI interface. DFRobot SEN0515
zł69.74
24h
Available quantity: 2
Available
The module with the natural gas and LPG concentration sensor (modMQ-5) allows the measurement of the concentration of natural gas, carbon monoxide, alcohol and methane. The module has an analogue output and an output triggered by exceeding the threshold of sensitivity.
zł7.90
24h
Available quantity: 8
Available
Module with a CO2 sensor based on the XENSIV PAS CO2 system from Infineon. It enables precise measurement of CO2 concentration in ppm via I2C, UART and PWM interfaces. SparkFun SEN-2295
zł339.00
3 weeks
No product available!
Available
Module with CO2, temperature and humidity sensor SCD-40. Equipped with a STEMMA QT connector, it communicates via the I2C interface. Adafruit 5187
zł253.31
24h
Available quantity: 1
Available
Module with integrated BME688 gas, pressure, temperature and humidity sensor placed in one MEMS housing. It is equipped with an I2C interface. Adafruit 5046
zł101.84
24h
Available quantity: 1
Available
Module with hydrogen sulphide sensor made in MEMS technology. It allows gas detection in the range of 0.5 to 50 ppm and has an analog output. DFRobot SEN0568
zł41.41
24h
Available quantity: 1
Available
Module with the MQ3 alcohol concentration sensor. The board is equipped with a Grove connector and communicates via an analog interface. Seeed Studio 101020006
zł61.78
24h
Available quantity: 2
Available
zł24.90
24h
Available quantity: 2
Available
Module with ozone detection sensor. It performs measurements up to 10 ppm with a resolution of 0.01 ppm. It has a UART output and an analog output. ZE25-O3
zł252.05
24h
Available quantity: 1
Available
Module with air quality sensor SGP30. It allows you to read the concentration of VOC (TVOC) and eCO2 and communicates via the I2C interface. Pimoroni PIM480
zł102.93
24h
Available quantity: 2
Available
Carbon monoxide sensor module made in MEMS technology. It allows gas detection in the range of 5 to 5000 ppm and has an analog output. DFRobot SEN0564